Skip to content
worldfires
CA · Canada · –

Wood Buffalo fire, 25 August 2022 Wood Buffalo

Out · last detection 6 Oct 2022, 20:20 UTC

The fire started on 25 August 2022 in Wood Buffalo, Canada, and satellites saw it burning for 43 days. Canada’s CWFIS (Natural Resources Canada) mapped an official burnt perimeter of 1,266 hectares from satellite imagery, spread across a single census subdivision.

It is the 162th largest in Alberta since 2016 (of 172 with a page). Number 173 in Canada in 2022, of 197.

Burnt area
1,266ha
official perimeter (CWFIS)
Duration
43days
25 Aug 2022 – 6 Oct 2022
Census subdivisions hit
1
municipalities
Started on
25 Aug
2022
Heat detections
119
in a single hotspot: 45 MW
Danger at start
21
Moderate · FWI index
Average daily power
60MW
detected power per day, on average

Where it burned

HOTSPOTS BY DAY 25 Aug6 Oct
6 Oct 2022

How it evolved, day by day

25 Aug 2022 · 5 MW · 1 26 Aug 2022 · 217 MW · 12 27 Aug 2022 · 17 MW · 15 16 Sept 2022 · 0 MW · 1 23 Sept 2022 · 16 MW · 4 24 Sept 2022 · 1 MW · 1 27 Sept 2022 · 58 MW · 7 28 Sept 2022 · 11 MW · 11 2 Oct 2022 · 215 MW · 22 3 Oct 2022 · 111 MW · 43 6 Oct 2022 · 15 MW · 2
26 Aug 27 Sept 3 Oct

Fire radiative power detected each day, in megawatts, and number of hotspots. The magenta bar marks the peak day.

The weather it burned in

32°high
62km/h · peak gust
25%lowest humidity

It had gone 6 days without rain (1 mm or more) when it started. Rain came after the fire: 2.0 mm on 11 Oct.

This area had burned before

No earlier perimeters overlap this fire since 2016, when the satellite record begins.

How big is it?

10 km
It burned the equivalent of 0.8% of the area of London (13 km² against 1,583 km²).

London boundary: geoBoundaries · Office for National Statistics (Open Government Licence v3.0).

This compares size, not location: both shapes are at the same scale, north up, centred on each other.

What happened to each census subdivision

  1. Wood Buffalo where it started
    1,324 ha
    0.0 %

Burnt area inside each census subdivision, from crossing the official perimeter with administrative boundaries. The distance runs from the point marking the centre of each area to the nearest fire: staying a kilometre away does not mean it reached the houses.

People and buildings inside the perimeter

GHSL 2020
Built-up area< 0.1 ha
Residents< 20

Inside the perimeter there was no noticeable built-up land and almost nobody lived there (GHSL 2020, satellite-based estimate).

This is an estimate on 100 m cells, made from satellite imagery and census data: it does not mean that homes burned or that anyone was harmed. The perimeter also contains land that never burned.

Source: Global Human Settlement Layer (GHS-BUILT-S and GHS-POP R2023A), European Commission Joint Research Centre (JRC), © European Union, CC BY 4.0. Sum inside the perimeter computed by WorldFires. human-settlement.emergency.copernicus.eu

The weather day by day

ECMWF ERA5 reanalysis at the fire location, the standard reference for past weather, and the Canadian Fire Weather Index (the same system Copernicus uses), computed by WorldFires from that data. Days after the fire run until the first rain.

Open-Meteo.com (CC BY 4.0) · Copernicus Climate Change Service (ERA5)

Day High Min. humidity Peak gust Rain Danger (FWI)
22 Aug 27.4 °C 36 % 30 km/h 0.1 mm Moderate 21
23 Aug 20.2 °C 31 % 25 km/h 0.2 mm Moderate 18
24 Aug 30.2 °C 40 % 31 km/h 0.0 mm Moderate 21
25 Aug 31.5 °C 35 % 26 km/h 0.0 mm Moderate 21
26 Aug 31.2 °C 32 % 32 km/h 0.1 mm High 26
27 Aug 19.9 °C 63 % 28 km/h 0.3 mm Moderate 16
28 Aug 17.9 °C 64 % 25 km/h 6.2 mm Very low 0
29 Aug 21.3 °C 43 % 32 km/h 0.1 mm Very low 5
30 Aug 18.7 °C 66 % 41 km/h 0.4 mm Low 11
31 Aug 22.5 °C 33 % 40 km/h 0.0 mm Moderate 20
1 Sept 16.9 °C 65 % 48 km/h 14.2 mm Very low 0
2 Sept 23.1 °C 39 % 31 km/h 0.0 mm Very low 3
3 Sept 28.9 °C 36 % 27 km/h 0.0 mm Low 10
4 Sept 27.9 °C 39 % 25 km/h 0.0 mm Moderate 13
5 Sept 21.8 °C 33 % 36 km/h 0.2 mm Moderate 17
6 Sept 19.1 °C 41 % 57 km/h 0.0 mm High 28
7 Sept 15.7 °C 51 % 34 km/h 0.0 mm Moderate 13
8 Sept 12.2 °C 44 % 62 km/h 0.0 mm High 27
9 Sept 15.3 °C 43 % 42 km/h 0.2 mm Moderate 17
10 Sept 22.1 °C 32 % 41 km/h 0.0 mm Moderate 18
11 Sept 17.3 °C 36 % 51 km/h 0.0 mm High 24
12 Sept 13.0 °C 44 % 35 km/h 0.0 mm Moderate 18
13 Sept 19.4 °C 31 % 34 km/h 0.0 mm Moderate 20
14 Sept 21.8 °C 29 % 26 km/h 0.0 mm Moderate 18
15 Sept 24.2 °C 27 % 36 km/h 0.0 mm High 24
16 Sept 22.4 °C 48 % 32 km/h 0.0 mm Moderate 20
17 Sept 15.4 °C 80 % 24 km/h 4.2 mm Very low 2
18 Sept 14.2 °C 55 % 19 km/h 0.0 mm Very low 1
19 Sept 13.8 °C 55 % 33 km/h 1.2 mm Very low 3
20 Sept 14.7 °C 39 % 32 km/h 0.2 mm Low 6
21 Sept 18.9 °C 39 % 36 km/h 0.0 mm Moderate 14
22 Sept 24.0 °C 34 % 30 km/h 0.0 mm Moderate 18
23 Sept 17.5 °C 25 % 48 km/h 0.0 mm High 30
24 Sept 14.1 °C 40 % 52 km/h 0.1 mm High 31
25 Sept 13.1 °C 49 % 28 km/h 0.0 mm Moderate 17
26 Sept 17.3 °C 29 % 33 km/h 0.0 mm Moderate 13
27 Sept 26.0 °C 39 % 38 km/h 0.0 mm High 24
28 Sept 23.4 °C 43 % 38 km/h 0.0 mm Moderate 18
29 Sept 11.3 °C 47 % 23 km/h 0.0 mm Moderate 16
30 Sept 16.6 °C 56 % 37 km/h 1.4 mm Low 9
1 Oct 20.7 °C 53 % 42 km/h 0.0 mm Moderate 13
2 Oct 17.9 °C 27 % 58 km/h 0.0 mm High 36
3 Oct 16.2 °C 32 % 35 km/h 0.0 mm High 26
4 Oct 11.4 °C 46 % 38 km/h 0.0 mm High 22
5 Oct 6.3 °C 50 % 22 km/h 0.0 mm Moderate 15
6 Oct 15.9 °C 45 % 42 km/h 0.0 mm High 22
7 Oct after 16.9 °C 48 % 24 km/h 0.0 mm Moderate 16
8 Oct after 14.0 °C 48 % 14 km/h 0.0 mm Moderate 12
9 Oct after 18.5 °C 35 % 30 km/h 0.0 mm Moderate 18
10 Oct after 14.4 °C 41 % 34 km/h 0.4 mm Moderate 20
11 Oct after 7.7 °C 51 % 62 km/h 2.0 mm Low 11

Its twins: fires that started in the same weather

It started with an FWI of 21.2, a minimum humidity of 35% and 6 days without rain. Fires in the area that started in weather like this since 2016: 30.

FWI at the start 21.2
Minimum humidity 35 %
Days without rain 6
this fire chosen twins rest of the area
Almost identicalSimilar

Outlines of the closest twins

Region 5, Unorganized fire, July 2024
19,715 ha 30 days FWI 20.3 Min. humidity 35 % 217 km away, in 2024

First rain (1 mm or more) after it ended: 1.3 mm on 15 Aug.

What happened to them

23 days
median duration
5,165 ha
median area
30 %
went past 10,000 ha
4.9 mm
rain at the end (median; 30 of 30 had it)

It stayed below its twins: 1,266 ha against a median of 5,165 ha. It lasted 43 days, against 23 days.

All of them had rain in the ten days after the end: the first rainy day brought a median of 4.9 mm.

This is a bank of analogues: it shows what usually happens, not what will happen. With fewer than 15 twins we give no figures. How we calculate it

How it ended

2.0 mmfirst rain
11 Oct5 days after it ended
62km/h · max. gust

It was considered over on 6 Oct, and on 11 Oct 2.0 mm fell. We do not know whether the rain or the firefighters put it out. Twins with rain when they ended: 30 of 30, with a median of 4.9 mm.

Weather on this page: Open-Meteo.com (CC BY 4.0) · Copernicus Climate Change Service (ERA5)

How a twin is chosen

  • Same area: fires that have already ended, less than 250 km from this one, since 2016.
  • Same start: we compare the FWI on the first day, the minimum humidity that day and the run of days without rain before it. The slider sets how much they may differ.
  • Only pages with final weather data (ERA5 reanalysis) calculated in the same way as this fire’s; agricultural and grass burns and pages with data under review are left out.
  • Fires burning at the same time as this one (a week before or after) are left out: they share the same spell of weather and do not count as a precedent.
  • They are sorted by similarity, and the outlines of the first five are drawn.

How we calculate it

Before and after, from space

Drag the line to compare the same ground before the fire and after it.

Before · 18 Aug 2022
After · 13 Oct 2022

If the day is cloudy, change the date: each satellite passes once a day. In false colour the burnt ground looks brown or red.

The smoke

CAMS · Copernicus

On 29 August 2022 the air beside the fire reached 339 µg/m³ of PM2.5. That day averaged 150: 10.0 times the WHO daily guideline (15).

PM2.5 peak339 µg/m³
Days over the guideline17 days
PM10484 µg/m³
Optical depth1.67
20 Aug31 Aug11 Sept22 Sept3 Oct
Good Fair Moderate Poor Very poor Extremely poor

Particles from the Copernicus CAMS model at the centre of the perimeter; these are not measurements in each town. The pale bar is the worst hour, the solid one the daily average.

Open-Meteo.com (CC BY 4.0) · Copernicus Atmosphere Monitoring Service (CAMS)

Detections table · 119Every satellite heat detection, one by one, with time, satellite, power and coordinates.
⬇ Download CSV Times in UTC. Each detection is a 375 m pixel: a large fire yields hundreds per pass.
Date and timeSatelliteFRP (MW)LatLon

Other fires nearby

All fires in Canada

Frequently asked questions

How long did the Wood Buffalo fire last?
It burned between 25 August 2022 and 6 October 2022: 43 days, according to the dates recorded by Canada’s CWFIS and the heat detections seen by satellite.
How much area did it burn?
The official perimeter mapped by Canada’s CWFIS (Natural Resources Canada) is 1,266 hectares (12.7 km²). Other tallies, such as those of provincial agencies, may give slightly different figures.
Which census subdivisions burned?
The fire only entered Wood Buffalo (1,324 ha, 0.0 %).
What was the weather like?
During the fire the temperature reached 31.5 °C, humidity dropped to 25 % and gusts hit 62 km/h. The fire danger index (FWI) reached 36, class High.
Where does this data come from?
From the official burnt perimeter of Canada’s CWFIS (NBAC, Natural Resources Canada) or, for the current season and until NBAC publishes it, the one rebuilt by GWIS (Copernicus); from NASA FIRMS VIIRS hotspots; and from the administrative boundaries of Canada. It is not an official report.
How did the fires that started in similar weather in this area end?
Fires less than 250 km away that started since 2016 with a similar FWI, humidity and dry spell: 30. Their median duration was 23 days and their median area 5,165 ha; 30 % went past 10,000 ha. All of them had rain in the ten days after the end: the first rainy day brought a median of 4.9 mm.

Where to verify it

A satellite detection is not an official report. Final figures and the fire’s status are published by each country’s emergency service.

Emergency number: 911 · Emergency number and official warnings

Satellite cross-check

History of this page Changes in area, dates, name, official record or merged pages, compared every night since 24 October 2026.

Does something look wrong on this page?

This page is built from satellite data and official records, and it sometimes gets things wrong: the wrong dates, the wrong town, two fires merged into one, or something that was not a wildfire at all. If you know this fire first-hand (you live nearby, saw it, fought it or reported on it), tell us what really happened and we will check it.

Report an error
What do you think is wrong?

We will only use your email to reply about this report. Privacy. This is not an emergency service: if there is a fire now, call 911.

How we know this
  • Perimeter: NBAC (Natural Resources Canada), official.
  • Dates from the perimeter: the VIIRS detections inside it did not change them. 119 Suomi-NPP VIIRS detections on those dates.
  • We have not matched this page with any official record.
  • Weather: Copernicus ERA5 reanalysis at the fire location, in cells of about 25 km.
  • Built-up area and population come from the JRC Global Human Settlement Layer (epoch 2020, 100 m cells), summed inside the perimeter: an estimate of what was there, not a damage count.

How we build fire pages: methodology

Where this data comes from

The perimeter is official: it comes from the National Burned Area Composite (NBAC) of the Canadian Wildland Fire Information System (CWFIS), Natural Resources Canada, which maps it on satellite imagery and publishes it under the Open Government Licence – Canada. Until NBAC publishes the current season, this year’s fires carry the perimeter rebuilt from heat detections by GWIS (Copernicus, CC BY 4.0), which is approximate. Heat detections come from the VIIRS sensors aboard Suomi-NPP and NOAA-20, distributed by NASA FIRMS at 375 m resolution. Census subdivision boundaries come from geoBoundaries ADM3 (Open Data Commons Open Database License 1.0). The area per census subdivision is computed by WorldFires by crossing the perimeter with those boundaries, so it may differ slightly from official figures.