Loupian fire, September 2019 Loupian
The fire started on 8 September 2019 in Loupian, France, and satellites saw it burning for 1 day. Copernicus mapped a burnt perimeter of 202 hectares from satellite imagery, spread across a single municipality.
It is the 9th largest in Hérault since 2016 (of 14 with a page). Number 10 in France in 2019, of 26.
The power measured by the satellite is low (12.4 MW in the strongest hotspot), more typical of grass or stubble burning, or a slow surface fire, than of a large crown fire.
Compare with…
- Burnt area
- 202ha
- Copernicus perimeter
- Duration
- 1day
- 8 Sept 2019 – 8 Sept 2019
- Municipalities hit
- 1
- communes
- Started on
- 8 Sept
- 2019
- Heat detections
- 1
- in a single hotspot: 12 MW
- Danger at start
- 36
- High · FWI index
- Average daily power
- 12MW
- detected power per day, on average
Where it burned
How it evolved, day by day
8 Sept 2019 · 12 MW · 1
Fire radiative power detected each day, in megawatts, and number of hotspots. The magenta bar marks the peak day.
The weather it burned in
It had gone 18 days without rain (1 mm or more) when it started. Rain came after the fire: 25.1 mm on 10 Sept.
This area had burned before
No earlier perimeters overlap this fire since 2016, when the satellite record begins.
What happened to each town
-
202 ha reached on 8 Sept8.7 %
Burnt area inside each municipality, from crossing the official perimeter with administrative boundaries. The distance runs from the point marking the centre of each area to the nearest fire: staying a kilometre away does not mean it reached the houses.
What burned
- Agricultural areas84 %
- Sclerophyllous scrub14 %
- Artificial surfaces1.5 %
Land cover inside the perimeter according to Corine Land Cover, as reported by Copernicus.
Official record
According to BDIFF, a fire of 237 ha was recorded in Loupian on 8 September 2019 (the satellite measured 202 ha). The record has no coordinates, so it was matched by municipality and date.
- Loupian 8 September 2019 · 14:37 237 ha · cause: negligence
BDIFF (Base de Données sur les Incendies de Forêts en France). This is the agency’s consolidated statistic: it measures the area in its own way, which is why it can differ from the satellite.
The weather day by day
ECMWF ERA5 reanalysis at the fire location, the standard reference for past weather, and the Canadian Fire Weather Index (the same system Copernicus uses), computed by WorldFires from that data. Days after the fire run until the first rain.
Open-Meteo.com (CC BY 4.0) · Copernicus Climate Change Service (ERA5)
| Day | High | Min. humidity | Peak gust | Rain | Danger (FWI) |
|---|---|---|---|---|---|
| 8 Sept | 24.4 °C | 29 % | 43 km/h | 0.0 mm | High 36 |
| 9 Sept after | 22.2 °C | 35 % | 35 km/h | 0.0 mm | High 28 |
| 10 Sept after | 19.6 °C | 58 % | 40 km/h | 25.1 mm | Very low 1 |
Before and after, from space
Drag the line to compare the same ground before the fire and after it.
If the day is cloudy, change the date: each satellite passes once a day. In false colour the burnt ground looks brown or red.
The smoke
CAMS · CopernicusOn 7 September 2019 the air beside the fire reached 7 µg/m³ of PM2.5, but no daily average passed the WHO guideline (15).
Particles from the Copernicus CAMS model at the centre of the perimeter; these are not measurements in each town. The pale bar is the worst hour, the solid one the daily average.
Open-Meteo.com (CC BY 4.0) · Copernicus Atmosphere Monitoring Service (CAMS)
Detections table · 1Every satellite heat detection, one by one, with time, satellite, power and coordinates.
| Date and time | Satellite | FRP (MW) | Lat | Lon |
|---|
Other fires nearby
Frequently asked questions
- How long did the Loupian fire last?
- Copernicus dates it between 8 September 2019 and 8 September 2019: 1 day between the first and last image with fire.
- How much area did it burn?
- The perimeter Copernicus measured from satellite imagery is 202 hectares (2.0 km²). Official national figures may differ.
- Which municipalities burned?
- The fire only entered Loupian (202 ha, 8.7 %).
- Did the fire reach a town?
- The fire started in Loupian and reached its centre: the point marking it was inside the burnt area or less than 500 metres from it. That does not mean houses burned.
- What was the weather like?
- During the fire the temperature reached 24.4 °C, humidity dropped to 29 % and gusts hit 43 km/h. The fire danger index (FWI) reached 36, class High.
- Where does this data come from?
- From the EFFIS (Copernicus) burnt perimeter, NASA FIRMS VIIRS hotspots and the administrative boundaries of France (geoBoundaries). It is not an official report.
Where to verify it
A satellite detection is not an official report. Final figures and the fire’s status are published by each country’s emergency service.
Emergency number: 112 · 18 · Emergency number and official warnings ›
Satellite cross-check
History of this page Changes in area, dates, name, official record or merged pages, compared every night since 24 October 2026.
No changes since 24 October 2026.
Does something look wrong on this page?
This page is built from satellite data and official records, and it sometimes gets things wrong: the wrong dates, the wrong town, two fires merged into one, or something that was not a wildfire at all. If you know this fire first-hand (you live nearby, saw it, fought it or reported on it), tell us what really happened and we will check it.
Report an error
How we know this
- Perimeter: EFFIS (Copernicus), mapped on satellite imagery.
- Dates from the perimeter: the VIIRS detections inside it did not change them. One Suomi-NPP VIIRS detection on those dates.
- Compared with BDIFF: 237 official ha against 202 ha of perimeter; they agree within 25%.
- Weather: Copernicus ERA5 reanalysis at the fire location, in cells of about 25 km.
Where this data comes from
The perimeter and land cover come from the Copernicus European Forest Fire Information System (EFFIS), measured on MODIS and Sentinel-2 imagery and published under CC BY 4.0. Heat detections come from the VIIRS sensors aboard Suomi-NPP and NOAA-20, distributed by NASA FIRMS at 375 m resolution. Municipal boundaries come from geoBoundaries ADM5 (Open Data Commons Attribution License 1.0). The area per municipality is computed by WorldFires by crossing the perimeter with those boundaries, so it may differ slightly from each country’s official figure.