Skip to content
worldfires
ES · Spain · →

Lobeira fire, September 2016 Lobeira

Out · last detection 8 Sept 2016, 02:12 UTC

The fire started on 7 September 2016 in Lobeira, Spain, and satellites saw it burning for 2 days. Copernicus mapped a burnt perimeter of 299 hectares from satellite imagery, spread across a single municipality.

It is the 59th largest in Ourense since 2016 (of 118 with a page). Number 39 in Spain in 2016, of 69.

Burnt area
299ha
Copernicus perimeter
Duration
2days
7 Sept 2016 – 8 Sept 2016
Municipalities hit
1
municipalities
Started on
7 Sept
2016
Heat detections
20
in a single hotspot: 35 MW
Danger at start
23
High · FWI index
Energy released
185MW
sum of detected power

Where it burned

8 Sept 2016
HOTSPOTS BY DAY 7 Sept8 Sept

How it evolved, day by day

78

Fire radiative power detected each day, in megawatts, and number of hotspots. The magenta bar marks the peak day.

The weather it burned in

26°high
35km/h · peak gust
36%lowest humidity

It had gone 11 days without rain (1 mm or more) when it started. Rain came after the fire: 32.7 mm on 13 Sept.

This area had burned before

No earlier perimeters overlap this fire since 2016, when the satellite record begins.

What happened to each town

  1. Lobeira 703 inhabitants · 1.7 km from the town where it started
    300 ha reached on 7 Sept
    4.4 %

Burnt area inside each municipality, from crossing the official perimeter with administrative boundaries. The distance is from the town centre to the nearest fire: staying a kilometre away does not mean it reached the houses.

What burned

  • Other natural land91 %
  • Broadleaved forest5.3 %
  • Agricultural areas3.3 %

Natura 2000 protected area affected: 99 %

Natura 2000 sites (European Environment Agency, 2024 release) crossed by the perimeter.

Land cover inside the perimeter according to Corine Land Cover, as reported by Copernicus.

Official record

According to EGIF (MITECO), 2 fires started inside this perimeter on these dates, totalling 376 ha (the satellite measured 299 ha). The two figures differ a lot, so these may not be exactly the same fire: take them as nearby records.

MITECO, Estadística General de Incendios Forestales (EGIF). This is the agency’s consolidated statistic: it measures the area in its own way, which is why it can differ from the satellite.

The weather day by day

ECMWF ERA5 reanalysis at the fire location, the standard reference for past weather, and the Canadian Fire Weather Index (the same system Copernicus uses), computed by WorldFires from that data. Days after the fire run until the first rain.

Open-Meteo.com (CC BY 4.0) · Copernicus Climate Change Service (ERA5)

Day High Min. humidity Peak gust Rain Danger (FWI)
7 Sept 25.9 °C 36 % 34 km/h 0.0 mm High 23
8 Sept 20.5 °C 45 % 35 km/h 0.0 mm Moderate 20
9 Sept after 20.8 °C 35 % 35 km/h 0.0 mm Moderate 20
10 Sept after 20.9 °C 59 % 32 km/h 0.0 mm Moderate 15
11 Sept after 23.6 °C 46 % 27 km/h 0.0 mm Moderate 15
12 Sept after 24.2 °C 42 % 51 km/h 0.0 mm Moderate 19
13 Sept after 15.2 °C 63 % 58 km/h 32.7 mm Very low 0

Before and after, from space

Drag the line to compare the same ground before the fire and after it.

Before · 31 Aug 2016
After · 15 Sept 2016

If the day is cloudy, change the date: each satellite passes once a day. In false colour the burnt ground looks brown or red.

The smoke

CAMS · Copernicus

On 7 September 2016 the air beside the fire reached 196 µg/m³ of PM2.5. That day averaged 93: 6.2 times the WHO daily guideline (15).

PM2.5 peak196 µg/m³
Days over the guideline3 days
PM10206 µg/m³
567891011
Good Fair Moderate Poor Very poor Extremely poor

Particles from the Copernicus CAMS model at the centre of the perimeter; these are not measurements in each town. The pale bar is the worst hour, the solid one the daily average.

Open-Meteo.com (CC BY 4.0) · Copernicus Atmosphere Monitoring Service (CAMS)

Detections table · 20Every satellite heat detection, one by one, with time, satellite, power and coordinates.
⬇ Download CSV Times in UTC. Each detection is a 375 m pixel: a large fire yields hundreds per pass.
Date and timeSatelliteFRP (MW)LatLon

Other fires nearby

All fires in Spain ›

Frequently asked questions

How long did the Lobeira fire last?
Copernicus dates it between 7 September 2016 and 8 September 2016: 2 days between the first and last image with fire.
How much area did it burn?
The perimeter Copernicus measured from satellite imagery is 299 hectares (3.0 km²). Official national figures may differ.
Which municipalities burned?
The fire only entered Lobeira (300 ha, 4.4 %).
Did the fire reach a town?
The closest fire to a town centre came within 1.7 km of Lobeira. That is the distance to the perimeter or nearest hotspot; it does not mean it entered the houses.
What was the weather like?
During the fire the temperature reached 25.9 °C, humidity dropped to 36 % and gusts hit 35 km/h. The fire danger index (FWI) reached 23, class High.
Where does this data come from?
From the EFFIS (Copernicus) burnt perimeter, NASA FIRMS VIIRS hotspots and the administrative boundaries of Spain (geoBoundaries). It is not an official report.

Where to verify it

A satellite detection is not an official report. Final figures and the fire’s status are published by each country’s emergency service.

Emergency number: 112

Satellite cross-check

Does something look wrong on this page?

This page is built from satellite data and official records, and it sometimes gets things wrong: the wrong dates, the wrong town, two fires merged into one, or something that was not a wildfire at all. If you know this fire first-hand (you live nearby, saw it, fought it or reported on it), tell us what really happened and we will check it.

Report an error
What do you think is wrong?

We will only use your email to reply about this report. Privacy. This is not an emergency service: if there is a fire now, call 112.

Where this data comes from

The perimeter and land cover come from the Copernicus European Forest Fire Information System (EFFIS), measured on MODIS and Sentinel-2 imagery and published under CC BY 4.0. Heat detections come from the VIIRS sensors aboard Suomi-NPP and NOAA-20, distributed by NASA FIRMS at 375 m resolution. Municipal boundaries come from geoBoundaries ADM3 (Creative Commons Attribution 4.0 International (CC BY 4.0)). The area per municipality is computed by WorldFires by crossing the perimeter with those boundaries, so it may differ slightly from each country’s official figure.