Skip to content
worldfires
BR · Brazil · –

Formosa do Rio Preto fire, August 2019 Formosa do Rio Preto

Out · last detection 13 Sept 2019, 16:18 UTC

The fire started on 27 August 2019 in Formosa do Rio Preto, Brazil, and satellites saw it burning for 18 days. Copernicus’s global GWIS system rebuilt a burnt perimeter of 9,387 hectares from heat detections, spread across a single municipality.

It is the 85th largest in Bahia since 2016 (of 386 with a page). Number 185 in Brazil in 2019, of 973.

Burnt area
9,387ha
GWIS perimeter (Copernicus)
Duration
18days
27 Aug 2019 – 13 Sept 2019
Municipalities hit
1
municipalities
Started on
27 Aug
2019
Heat detections
331
in a single hotspot: 389 MW
Danger at start
43
Very high · FWI index
Average daily power
506MW
detected power per day, on average

Where it burned

HOTSPOTS BY DAY 27 Aug13 Sept
13 Sept 2019

How it evolved, day by day

27 Aug 2019 · 14 MW · 11 28 Aug 2019 · 48 MW · 13 29 Aug 2019 · 25 MW · 5 30 Aug 2019 · 191 MW · 41 31 Aug 2019 · 51 MW · 4 1 Sept 2019 · 55 MW · 3 2 Sept 2019 · 660 MW · 11 3 Sept 2019 · 376 MW · 30 4 Sept 2019 · 1,584 MW · 53 5 Sept 2019 · 984 MW · 39 6 Sept 2019 · 3,070 MW · 70 7 Sept 2019 · 1,285 MW · 37 8 Sept 2019 · 98 MW · 2 10 Sept 2019 · 46 MW · 5 11 Sept 2019 · 8 MW · 4 12 Sept 2019 · 61 MW · 2 13 Sept 2019 · 49 MW · 1
27 Aug 31 Aug 6 Sept 13 Sept

Fire radiative power detected each day, in megawatts, and number of hotspots. The magenta bar marks the peak day.

The weather it burned in

35°high
55km/h · peak gust
22%lowest humidity

It had gone more than two months without rain (1 mm or more) when it started.

This area had burned before

2% of the perimeter overlaps earlier fires recorded since 2016: 159 ha in 2017.

How big is it?

10 km
It burned the equivalent of 5.9% of the area of London (94 km² against 1,583 km²).

London boundary: geoBoundaries · Office for National Statistics (Open Government Licence v3.0).

This compares size, not location: both shapes are at the same scale, north up, centred on each other.

What happened to each town

  1. Formosa do Rio Preto 25,899 inhabitants where it started
    9,440 ha reached on 27 Aug
    0.6 %

Burnt area inside each municipality, from crossing the GWIS perimeter with administrative boundaries. The distance runs from the point marking the centre of each area to the nearest fire: staying a kilometre away does not mean it reached the houses.

People and buildings inside the perimeter

GHSL 2020
Built-up area< 0.1 ha
Residents< 20

Inside the perimeter there was no noticeable built-up land and almost nobody lived there (GHSL 2020, satellite-based estimate).

This is an estimate on 100 m cells, made from satellite imagery and census data: it does not mean that homes burned or that anyone was harmed. The perimeter also contains land that never burned.

Source: Global Human Settlement Layer (GHS-BUILT-S and GHS-POP R2023A), European Commission Joint Research Centre (JRC), © European Union, CC BY 4.0. Sum inside the perimeter computed by WorldFires. human-settlement.emergency.copernicus.eu

The weather day by day

ECMWF ERA5 reanalysis at the fire location, the standard reference for past weather, and the Canadian Fire Weather Index (the same system Copernicus uses), computed by WorldFires from that data. Days after the fire run until the first rain.

Open-Meteo.com (CC BY 4.0) · Copernicus Climate Change Service (ERA5)

Started with 60 days without rain: 55 % of the area in Brazil

Day High Min. humidity Peak gust Rain Danger (FWI)
27 Aug 30.8 °C 31 % 45 km/h 0.0 mm Very high 43
28 Aug 31.1 °C 34 % 42 km/h 0.0 mm Very high 40
29 Aug 31.7 °C 32 % 42 km/h 0.0 mm Very high 40
30 Aug 31.5 °C 32 % 43 km/h 0.0 mm Very high 40
31 Aug 32.9 °C 28 % 38 km/h 0.0 mm Very high 39
1 Sept 33.5 °C 23 % 34 km/h 0.0 mm Very high 39
2 Sept 34.5 °C 22 % 33 km/h 0.0 mm Very high 40
3 Sept 34.6 °C 23 % 35 km/h 0.0 mm Very high 41
4 Sept 34.4 °C 27 % 38 km/h 0.0 mm Very high 43
5 Sept 34.7 °C 25 % 36 km/h 0.0 mm Very high 42
6 Sept 32.9 °C 26 % 51 km/h 0.0 mm Extreme 51
7 Sept 32.3 °C 29 % 54 km/h 0.0 mm Extreme 53
8 Sept 33.0 °C 27 % 55 km/h 0.0 mm Extreme 52
9 Sept 32.8 °C 32 % 47 km/h 0.0 mm Very high 46
10 Sept 34.1 °C 28 % 41 km/h 0.0 mm Very high 44
11 Sept 33.5 °C 27 % 40 km/h 0.0 mm Very high 42
12 Sept 34.0 °C 24 % 37 km/h 0.0 mm Very high 41
13 Sept 35.4 °C 25 % 37 km/h 0.0 mm Very high 42
14 Sept after 35.8 °C 19 % 35 km/h 0.0 mm Very high 44
15 Sept after 33.4 °C 26 % 37 km/h 0.0 mm Very high 47
16 Sept after 33.8 °C 28 % 48 km/h 0.0 mm Extreme 51
17 Sept after 34.1 °C 25 % 45 km/h 0.0 mm Extreme 50
18 Sept after 35.6 °C 25 % 36 km/h 0.0 mm Very high 44
19 Sept after 35.9 °C 24 % 37 km/h 0.0 mm Very high 45
20 Sept after 36.1 °C 25 % 40 km/h 0.0 mm Very high 48
21 Sept after 35.8 °C 24 % 33 km/h 0.0 mm Very high 43
22 Sept after 35.1 °C 26 % 31 km/h 0.0 mm Very high 43
23 Sept after 34.8 °C 23 % 40 km/h 0.0 mm Very high 48

Its twins: fires that started in the same weather

It started with an FWI of 43.1, a minimum humidity of 31% and more than two months without rain. Fires in the area that started in weather like this since 2016: 29.

FWI at the start 43.1
Minimum humidity 31 %
Days without rain 60+
this fire chosen twins rest of the area
Almost identicalSimilar

Outlines of the closest twins

Mateiros fire, August 2020
3,146 ha 9 days FWI 43.2 Min. humidity 32 % 61 km away, in 2020

First rain (1 mm or more) after it ended: none in the following ten days.

What happened to them

13 days
median duration
4,999 ha
median area
21 %
went past 10,000 ha
5.2 mm
rain at the end (median; 6 of 29 had it)

It was 1.9 times larger than the median of its twins and lasted 18 days, against 13 days.

Only 7 of its 29 twins burned more. The weather on the first day does not explain everything: the wind in the following days, the fuel and the firefighting also count. In 23 of 29, not even 1 mm fell in the ten days after the end: they went out without rain. In the rest, the first rainy day brought a median of 5.2 mm.

This is a bank of analogues: it shows what usually happens, not what will happen. With fewer than 15 twins we give no figures. How we calculate it

How it ended

—first rain
—no rain in ten days
55km/h · max. gust

It was considered over on 13 Sept, and not even 1 mm fell in the following ten days: it went out without rain. Twins with rain when they ended: 6 of 29, with a median of 5.2 mm.

Weather on this page: Open-Meteo.com (CC BY 4.0) · Copernicus Climate Change Service (ERA5)

How a twin is chosen

  • Same area: fires that have already ended, less than 250 km from this one, since 2016.
  • Same start: we compare the FWI on the first day, the minimum humidity that day and the run of days without rain before it. The slider sets how much they may differ.
  • Only pages with final weather data (ERA5 reanalysis) calculated in the same way as this fire’s; agricultural and grass burns and pages with data under review are left out.
  • Fires burning at the same time as this one (a week before or after) are left out: they share the same spell of weather and do not count as a precedent.
  • They are sorted by similarity, and the outlines of the first five are drawn.

How we calculate it

Before and after, from space

Drag the line to compare the same ground before the fire and after it.

Before · 20 Aug 2019
After · 20 Sept 2019

If the day is cloudy, change the date: each satellite passes once a day. In false colour the burnt ground looks brown or red.

Detections table · 331Every satellite heat detection, one by one, with time, satellite, power and coordinates.
⬇ Download CSV Times in UTC. Each detection is a 375 m pixel: a large fire yields hundreds per pass.
Date and timeSatelliteFRP (MW)LatLon

Other fires nearby

All fires in Brazil

Frequently asked questions

How long did the Formosa do Rio Preto fire last?
According to the heat detections seen by satellite inside the perimeter, it burned from 27 August 2019 to 13 September 2019 (18 days). The perimeter dates it from 30 August 2019 to 8 September 2019.
How much area did it burn?
The perimeter GWIS (Copernicus) rebuilt from heat detections is 9,387 hectares (93.9 km²). It is an estimate: official national figures may differ.
Which municipalities burned?
The fire only entered Formosa do Rio Preto (9,440 ha, 0.6 %).
What was the weather like?
During the fire the temperature reached 35.4 °C, humidity dropped to 22 % and gusts hit 55 km/h. The fire danger index (FWI) reached 53, class Extreme.
Where does this data come from?
From the GWIS (Copernicus) burnt perimeter, NASA FIRMS VIIRS hotspots and the administrative boundaries of Brazil (geoBoundaries). It is not an official report.
How did the fires that started in similar weather in this area end?
Fires less than 250 km away that started since 2016 with a similar FWI, humidity and dry spell: 29. Their median duration was 13 days and their median area 4,999 ha; 21 % went past 10,000 ha. Only 7 of its 29 twins burned more. The weather on the first day does not explain everything: the wind in the following days, the fuel and the firefighting also count. In 23 of 29, not even 1 mm fell in the ten days after the end: they went out without rain. In the rest, the first rainy day brought a median of 5.2 mm.

Where to verify it

A satellite detection is not an official report. Final figures and the fire’s status are published by each country’s emergency service.

Emergency number: 193 · Emergency number and official warnings

Satellite cross-check

History of this page · 2 Changes in area, dates, name, official record or merged pages, compared every night since 24 October 2026.
  1. Last day with fire: 8 September 2019 → 13 September 2019.
  2. Start date: 30 August 2019 → 27 August 2019.

RSS Changes to this page With cross-checks and a citable version

Does something look wrong on this page?

This page is built from satellite data and official records, and it sometimes gets things wrong: the wrong dates, the wrong town, two fires merged into one, or something that was not a wildfire at all. If you know this fire first-hand (you live nearby, saw it, fought it or reported on it), tell us what really happened and we will check it.

Report an error
What do you think is wrong?

We will only use your email to reply about this report. Privacy. This is not an emergency service: if there is a fire now, call 193.

How we know this
  • Perimeter: GWIS (Copernicus), rebuilt from heat detections rather than mapped on imagery.
  • Dates adjusted with the VIIRS detections inside the perimeter, which said 30 August 2019 to 8 September 2019. 331 Suomi-NPP VIIRS detections on those dates.
  • We have not matched this page with any official record.
  • Weather: Copernicus ERA5 reanalysis at the fire location, in cells of about 25 km.
  • Built-up area and population come from the JRC Global Human Settlement Layer (epoch 2020, 100 m cells), summed inside the perimeter: an estimate of what was there, not a damage count.

How we build fire pages: methodology

Where this data comes from

The perimeter comes from the Copernicus Global Wildfire Information System (GWIS), which rebuilds it from MODIS and VIIRS heat detections and publishes it under CC BY 4.0. It is not measured on imagery as in Europe, so it is an estimate. Heat detections come from the VIIRS sensors aboard Suomi-NPP and NOAA-20, distributed by NASA FIRMS at 375 m resolution. Municipal boundaries come from geoBoundaries ADM2 (Creative Commons Attribution 3.0 Intergovernmental Organisations (CC BY 3.0 IGO)). The area per municipality is computed by WorldFires by crossing the perimeter with those boundaries, so it may differ from each country’s official figure.