Skip to content
worldfires
RU · Russia · –

Evenkiysky Rayon fire, 10 July 2019 Evenkiysky Rayon

Out · last detection 10 Aug 2019, 19:14 UTC

The fire started on 10 July 2019 in Evenkiysky Rayon, Russia, and satellites saw it burning for 32 days. Copernicus’s global GWIS system rebuilt a burnt perimeter of 17,870 hectares from heat detections, spread across a single municipality.

It is the 65th largest in Krasnoyarsk Krai since 2016 (of 538 with a page). Number 80 in Russia in 2019, of 610.

Burnt area
17,870ha
GWIS perimeter (Copernicus)
Duration
32days
10 Jul 2019 – 10 Aug 2019
Municipalities hit
1
districts
Started on
10 Jul
2019
Heat detections
1,981
in a single hotspot: 589 MW
Danger at start
23
High · FWI index
Average daily power
761MW
detected power per day, on average

Where it burned

HOTSPOTS BY DAY 10 Jul10 Aug
10 Aug 2019

How it evolved, day by day

10 Jul 2019 · 11 MW · 7 11 Jul 2019 · 802 MW · 29 12 Jul 2019 · 1 MW · 1 13 Jul 2019 · 892 MW · 41 14 Jul 2019 · 21 MW · 20 15 Jul 2019 · 1,463 MW · 37 16 Jul 2019 · 379 MW · 112 17 Jul 2019 · 297 MW · 84 18 Jul 2019 · 1,100 MW · 311 19 Jul 2019 · 4,649 MW · 167 20 Jul 2019 · 3,191 MW · 161 21 Jul 2019 · 282 MW · 78 22 Jul 2019 · 199 MW · 59 23 Jul 2019 · 457 MW · 62 24 Jul 2019 · 65 MW · 33 25 Jul 2019 · 79 MW · 39 26 Jul 2019 · 150 MW · 25 29 Jul 2019 · 15 MW · 9 30 Jul 2019 · 99 MW · 23 31 Jul 2019 · 195 MW · 27 2 Aug 2019 · 4 MW · 3 3 Aug 2019 · 120 MW · 29 4 Aug 2019 · 400 MW · 60 5 Aug 2019 · 903 MW · 87 6 Aug 2019 · 3,643 MW · 154 7 Aug 2019 · 2,041 MW · 151 8 Aug 2019 · 249 MW · 60 9 Aug 2019 · 210 MW · 69 10 Aug 2019 · 150 MW · 43
10 Jul 19 Jul 30 Jul 6 Aug

Fire radiative power detected each day, in megawatts, and number of hotspots. The magenta bar marks the peak day.

The weather it burned in

31°high
56km/h · peak gust
27%lowest humidity

It had gone 23 days without rain (1 mm or more) when it started. Rain came after the fire: 6.0 mm on 11 Aug.

This area had burned before

4% of the perimeter overlaps earlier fires recorded since 2016: 30 ha in 2017, 616 ha in 2018.

How big is it?

10 km
It burned the equivalent of 11% of the area of London (179 km² against 1,583 km²).

London boundary: geoBoundaries · Office for National Statistics (Open Government Licence v3.0).

This compares size, not location: both shapes are at the same scale, north up, centred on each other.

What happened to each town

  1. Evenkiysky Rayon where it started
    15,608 ha reached on 10 Jul
    0.0 %

Burnt area inside each municipality, from crossing the GWIS perimeter with administrative boundaries. The distance runs from the point marking the centre of each area to the nearest fire: staying a kilometre away does not mean it reached the houses.

People and buildings inside the perimeter

GHSL 2020
Built-up area< 0.1 ha
Residents< 20

Inside the perimeter there was no noticeable built-up land and almost nobody lived there (GHSL 2020, satellite-based estimate).

This is an estimate on 100 m cells, made from satellite imagery and census data: it does not mean that homes burned or that anyone was harmed. The perimeter also contains land that never burned.

Source: Global Human Settlement Layer (GHS-BUILT-S and GHS-POP R2023A), European Commission Joint Research Centre (JRC), © European Union, CC BY 4.0. Sum inside the perimeter computed by WorldFires. human-settlement.emergency.copernicus.eu

The weather day by day

ECMWF ERA5 reanalysis at the fire location, the standard reference for past weather, and the Canadian Fire Weather Index (the same system Copernicus uses), computed by WorldFires from that data. Days after the fire run until the first rain.

Open-Meteo.com (CC BY 4.0) · Copernicus Climate Change Service (ERA5)

Day High Min. humidity Peak gust Rain Danger (FWI)
10 Jul 28.2 °C 32 % 16 km/h 0.0 mm High 23
11 Jul 27.7 °C 46 % 44 km/h 0.1 mm High 32
12 Jul 21.0 °C 46 % 35 km/h 0.3 mm High 30
13 Jul 25.4 °C 36 % 32 km/h 0.0 mm High 30
14 Jul 25.9 °C 40 % 16 km/h 0.0 mm High 23
15 Jul 25.7 °C 40 % 44 km/h 0.0 mm Very high 41
16 Jul 28.3 °C 46 % 39 km/h 0.0 mm High 34
17 Jul 30.6 °C 39 % 30 km/h 0.0 mm High 30
18 Jul 29.4 °C 32 % 42 km/h 0.0 mm High 34
19 Jul 21.0 °C 31 % 49 km/h 0.0 mm Very high 46
20 Jul 20.5 °C 35 % 56 km/h 0.0 mm Very high 50
21 Jul 21.9 °C 40 % 37 km/h 0.0 mm High 37
22 Jul 25.9 °C 34 % 27 km/h 0.0 mm High 32
23 Jul 25.8 °C 31 % 22 km/h 0.0 mm High 31
24 Jul 26.2 °C 34 % 13 km/h 0.0 mm High 25
25 Jul 27.5 °C 42 % 20 km/h 0.0 mm High 30
26 Jul 27.2 °C 42 % 15 km/h 0.0 mm High 27
27 Jul 25.1 °C 61 % 30 km/h 0.0 mm High 26
28 Jul 23.3 °C 53 % 44 km/h 0.0 mm High 31
29 Jul 24.0 °C 43 % 29 km/h 0.0 mm High 25
30 Jul 25.8 °C 36 % 16 km/h 0.0 mm High 24
31 Jul 25.9 °C 35 % 25 km/h 0.0 mm High 29
1 Aug 20.7 °C 76 % 33 km/h 4.5 mm Low 10
2 Aug 27.1 °C 46 % 28 km/h 0.0 mm Low 7
3 Aug 25.1 °C 45 % 31 km/h 0.0 mm Moderate 16
4 Aug 23.3 °C 35 % 29 km/h 0.0 mm High 26
5 Aug 24.0 °C 27 % 33 km/h 0.0 mm High 36
6 Aug 27.6 °C 29 % 26 km/h 0.0 mm High 34
7 Aug 26.9 °C 39 % 17 km/h 0.0 mm High 28
8 Aug 26.3 °C 38 % 21 km/h 0.0 mm High 30
9 Aug 26.4 °C 38 % 27 km/h 0.0 mm High 30
10 Aug 25.3 °C 41 % 31 km/h 0.4 mm High 30
11 Aug after 18.4 °C 60 % 30 km/h 6.0 mm Moderate 20

Its twins: fires that started in the same weather

It started with an FWI of 23.2, a minimum humidity of 32% and 23 days without rain. Fires in the area that started in weather like this since 2016: 43.

FWI at the start 23.2
Minimum humidity 32 %
Days without rain 23
this fire chosen twins rest of the area
Almost identicalSimilar

Outlines of the closest twins

Evenkiysky Rayon fire, September 2016
13,935 ha 17 days FWI 22.8 Min. humidity 31 % 75 km away, in 2016

First rain (1 mm or more) after it ended: 1.1 mm on 29 Sept.

What happened to them

17 days
median duration
5,308 ha
median area
33 %
went past 10,000 ha
3.9 mm
rain at the end (median; 41 of 43 had it)

It was 3.4 times larger than the median of its twins and lasted 32 days, against 17 days.

Only 8 of its 43 twins burned more. The weather on the first day does not explain everything: the wind in the following days, the fuel and the firefighting also count. In 2 of 43, not even 1 mm fell in the ten days after the end: they went out without rain. In the rest, the first rainy day brought a median of 3.9 mm.

This is a bank of analogues: it shows what usually happens, not what will happen. With fewer than 15 twins we give no figures. How we calculate it

How it ended

6.0 mmfirst rain
11 Augthe day after it ended
56km/h · max. gust

It was considered over on 10 Aug, and on 11 Aug 6.0 mm fell. We do not know whether the rain or the firefighters put it out. Twins with rain when they ended: 41 of 43, with a median of 3.9 mm.

Weather on this page: Open-Meteo.com (CC BY 4.0) · Copernicus Climate Change Service (ERA5)

How a twin is chosen

  • Same area: fires that have already ended, less than 250 km from this one, since 2016.
  • Same start: we compare the FWI on the first day, the minimum humidity that day and the run of days without rain before it. The slider sets how much they may differ.
  • Only pages with final weather data (ERA5 reanalysis) calculated in the same way as this fire’s; agricultural and grass burns and pages with data under review are left out.
  • Fires burning at the same time as this one (a week before or after) are left out: they share the same spell of weather and do not count as a precedent.
  • They are sorted by similarity, and the outlines of the first five are drawn.

How we calculate it

Before and after, from space

Drag the line to compare the same ground before the fire and after it.

Before · 3 Jul 2019
After · 17 Aug 2019

If the day is cloudy, change the date: each satellite passes once a day. In false colour the burnt ground looks brown or red.

Detections table · 1,981Every satellite heat detection, one by one, with time, satellite, power and coordinates.
⬇ Download CSV Times in UTC. Each detection is a 375 m pixel: a large fire yields hundreds per pass.
Date and timeSatelliteFRP (MW)LatLon

Other fires nearby

All fires in Russia

Frequently asked questions

How long did the Evenkiysky Rayon fire last?
GWIS (Copernicus) dates it between 10 July 2019 and 10 August 2019: 32 days between the first and last heat detection of the perimeter.
How much area did it burn?
The perimeter GWIS (Copernicus) rebuilt from heat detections is 17,870 hectares (178.7 km²). It is an estimate: official national figures may differ.
Which municipalities burned?
The fire only entered Evenkiysky Rayon (15,608 ha, 0.0 %).
What was the weather like?
During the fire the temperature reached 30.6 °C, humidity dropped to 27 % and gusts hit 56 km/h. The fire danger index (FWI) reached 50, class Very high.
Where does this data come from?
From the GWIS (Copernicus) burnt perimeter, NASA FIRMS VIIRS hotspots and the administrative boundaries of Russia (geoBoundaries). It is not an official report.
How did the fires that started in similar weather in this area end?
Fires less than 250 km away that started since 2016 with a similar FWI, humidity and dry spell: 43. Their median duration was 17 days and their median area 5,308 ha; 33 % went past 10,000 ha. Only 8 of its 43 twins burned more. The weather on the first day does not explain everything: the wind in the following days, the fuel and the firefighting also count. In 2 of 43, not even 1 mm fell in the ten days after the end: they went out without rain. In the rest, the first rainy day brought a median of 3.9 mm.

Where to verify it

A satellite detection is not an official report. Final figures and the fire’s status are published by each country’s emergency service.

Emergency number: 112 · Emergency number and official warnings

Satellite cross-check

History of this page · 1 Changes in area, dates, name, official record or merged pages, compared every night since 24 October 2026.
  1. Area: 18,621 → 17,870 ha.

RSS Changes to this page With cross-checks and a citable version

Does something look wrong on this page?

This page is built from satellite data and official records, and it sometimes gets things wrong: the wrong dates, the wrong town, two fires merged into one, or something that was not a wildfire at all. If you know this fire first-hand (you live nearby, saw it, fought it or reported on it), tell us what really happened and we will check it.

Report an error
What do you think is wrong?

We will only use your email to reply about this report. Privacy. This is not an emergency service: if there is a fire now, call 112.

How we know this
  • Perimeter: GWIS (Copernicus), rebuilt from heat detections rather than mapped on imagery; 2 polygons grouped in this page.
  • Dates from the perimeter: the VIIRS detections inside it did not change them. 1,981 Suomi-NPP VIIRS detections on those dates.
  • We have not matched this page with any official record.
  • Weather: Copernicus ERA5 reanalysis at the fire location, in cells of about 25 km.
  • Built-up area and population come from the JRC Global Human Settlement Layer (epoch 2020, 100 m cells), summed inside the perimeter: an estimate of what was there, not a damage count.

How we build fire pages: methodology

Where this data comes from

The perimeter comes from the Copernicus Global Wildfire Information System (GWIS), which rebuilds it from MODIS and VIIRS heat detections and publishes it under CC BY 4.0. It is not measured on imagery as in Europe, so it is an estimate. Heat detections come from the VIIRS sensors aboard Suomi-NPP and NOAA-20, distributed by NASA FIRMS at 375 m resolution. Municipal boundaries come from geoBoundaries ADM2 (Open Data Commons Open Database License 1.0). The area per municipality is computed by WorldFires by crossing the perimeter with those boundaries, so it may differ from each country’s official figure.