Skip to content
worldfires
IE · Ireland · →

Wicklow LEA-6 fire, June 2018 Wicklow LEA-6, Bray West LEA-4

Out · last detection 30 Jun 2018, 14:03 UTC

The fire started on 28 June 2018 in Wicklow LEA-6, Ireland, and satellites saw it burning for 3 days. Copernicus mapped a burnt perimeter of 250 hectares from satellite imagery, spread across 2 municipalities.

It is the 3th largest in Leinster since 2016 (of 10 with a page). Number 3 in Ireland in 2018, of 5.

The power measured by the satellite is low (16.0 MW in the strongest hotspot), more typical of grass or stubble burning, or a slow surface fire, than of a large crown fire.

Compare with…
Burnt area
250ha
Copernicus perimeter
Duration
3days
28 Jun 2018 – 30 Jun 2018
Municipalities hit
2
local electoral areas
Started on
28 Jun
2018
Heat detections
27
in a single hotspot: 16 MW
Danger at start
12
Moderate · FWI index
Average daily power
53MW
detected power per day, on average

Where it burned

HOTSPOTS BY DAY 28 Jun30 Jun
30 Jun 2018

How it evolved, day by day

28 Jun 2018 · 18 MW · 4 29 Jun 2018 · 59 MW · 9 30 Jun 2018 · 83 MW · 14
28 Jun 29 Jun 30 Jun

Fire radiative power detected each day, in megawatts, and number of hotspots. The magenta bar marks the peak day.

The weather it burned in

21°high
35km/h · peak gust
33%lowest humidity

It had gone 10 days without rain (1 mm or more) when it started.

This area had burned before

No earlier perimeters overlap this fire since 2016, when the satellite record begins.

What happened to each town

  1. Wicklow LEA-6 where it started
    190 ha reached on 28 Jun
    0.4 %
  2. 61 ha reached on 30 Jun
    0.5 %

Burnt area inside each municipality, from crossing the official perimeter with administrative boundaries. The distance runs from the point marking the centre of each area to the nearest fire: staying a kilometre away does not mean it reached the houses.

What burned

  • Other natural land100 %

Natura 2000 protected area affected: 98 %

Natura 2000 sites (European Environment Agency, 2024 release) crossed by the perimeter.

Land cover inside the perimeter according to Corine Land Cover, as reported by Copernicus.

The weather day by day

ECMWF ERA5 reanalysis at the fire location, the standard reference for past weather, and the Canadian Fire Weather Index (the same system Copernicus uses), computed by WorldFires from that data. Days after the fire run until the first rain.

Open-Meteo.com (CC BY 4.0) · Copernicus Climate Change Service (ERA5)

Day High Min. humidity Peak gust Rain Danger (FWI)
28 Jun 21.0 °C 39 % 35 km/h 0.0 mm Moderate 12
29 Jun 20.1 °C 33 % 31 km/h 0.0 mm Moderate 13
30 Jun 17.8 °C 49 % 31 km/h 0.0 mm Moderate 12
1 Jul after 18.0 °C 55 % 40 km/h 0.0 mm Moderate 13
2 Jul after 18.8 °C 45 % 43 km/h 0.0 mm Moderate 14
3 Jul after 17.2 °C 53 % 38 km/h 0.0 mm Moderate 13
4 Jul after 20.7 °C 47 % 28 km/h 0.0 mm Moderate 12
5 Jul after 16.9 °C 62 % 27 km/h 0.0 mm Low 11
6 Jul after 17.4 °C 71 % 20 km/h 0.2 mm Low 7
7 Jul after 19.2 °C 63 % 18 km/h 0.0 mm Low 7
8 Jul after 20.0 °C 57 % 19 km/h 0.0 mm Low 8
9 Jul after 17.2 °C 71 % 32 km/h 0.3 mm Low 9
10 Jul after 17.6 °C 63 % 30 km/h 0.0 mm Low 9

Before and after, from space

Drag the line to compare the same ground before the fire and after it.

Before · 21 Jun 2018
After · 7 Jul 2018

If the day is cloudy, change the date: each satellite passes once a day. In false colour the burnt ground looks brown or red.

The smoke

CAMS · Copernicus

On 29 June 2018 the air beside the fire reached 21 µg/m³ of PM2.5, but no daily average passed the WHO guideline (15).

PM2.5 peak21 µg/m³
Days over the guideline0 days
PM1023 µg/m³
2627282930123
Good Fair Moderate Poor Very poor Extremely poor

Particles from the Copernicus CAMS model at the centre of the perimeter; these are not measurements in each town. The pale bar is the worst hour, the solid one the daily average.

Open-Meteo.com (CC BY 4.0) · Copernicus Atmosphere Monitoring Service (CAMS)

Detections table · 27Every satellite heat detection, one by one, with time, satellite, power and coordinates.
⬇ Download CSV Times in UTC. Each detection is a 375 m pixel: a large fire yields hundreds per pass.
Date and timeSatelliteFRP (MW)LatLon

Other fires nearby

All fires in Ireland ›

Frequently asked questions

How long did the Wicklow LEA-6 fire last?
Copernicus dates it between 28 June 2018 and 30 June 2018: 3 days between the first and last image with fire.
How much area did it burn?
The perimeter Copernicus measured from satellite imagery is 250 hectares (2.5 km²). Official national figures may differ.
Which municipalities burned?
The fire entered 2 municipalities: Wicklow LEA-6 (190 ha, 0.4 %); Bray West LEA-4 (61 ha, 0.5 %).
What was the weather like?
During the fire the temperature reached 21.0 °C, humidity dropped to 33 % and gusts hit 35 km/h. The fire danger index (FWI) reached 13, class Moderate.
Where does this data come from?
From the EFFIS (Copernicus) burnt perimeter, NASA FIRMS VIIRS hotspots and the administrative boundaries of Ireland (geoBoundaries). It is not an official report.

Where to verify it

A satellite detection is not an official report. Final figures and the fire’s status are published by each country’s emergency service.

Emergency number: 999 · 112 · Emergency number and official warnings ›

Satellite cross-check

History of this page Changes in area, dates, name, official record or merged pages, compared every night since 24 October 2026.

No changes since 24 October 2026.

RSS Changes to this page

Does something look wrong on this page?

This page is built from satellite data and official records, and it sometimes gets things wrong: the wrong dates, the wrong town, two fires merged into one, or something that was not a wildfire at all. If you know this fire first-hand (you live nearby, saw it, fought it or reported on it), tell us what really happened and we will check it.

Report an error
What do you think is wrong?

We will only use your email to reply about this report. Privacy. This is not an emergency service: if there is a fire now, call 999 · 112.

How we know this
  • Perimeter: EFFIS (Copernicus), mapped on satellite imagery.
  • Dates from the perimeter: the VIIRS detections inside it did not change them. 27 Suomi-NPP VIIRS detections on those dates.
  • We have not matched this page with any official record.
  • Weather: Copernicus ERA5 reanalysis at the fire location, in cells of about 25 km.

How we build fire pages: methodology ›

Where this data comes from

The perimeter and land cover come from the Copernicus European Forest Fire Information System (EFFIS), measured on MODIS and Sentinel-2 imagery and published under CC BY 4.0. Heat detections come from the VIIRS sensors aboard Suomi-NPP and NOAA-20, distributed by NASA FIRMS at 375 m resolution. Municipal boundaries come from geoBoundaries ADM2 (Creative Commons Attribution 4.0 (CC BY 4.0)). The area per municipality is computed by WorldFires by crossing the perimeter with those boundaries, so it may differ slightly from each country’s official figure.