Vintar fire, February 2019 Vintar
The fire started on 8 February 2019 in Vintar, Philippines, and satellites saw it burning for 4 days. Copernicus’s global GWIS system rebuilt a burnt perimeter of 1,174 hectares from heat detections, spread across a single municipality.
It is the 12th largest in Ilocos Region since 2016 (of 17 with a page). Number 8 in Philippines in 2019, of 11.
The power measured by the satellite is low (15.8 MW in the strongest hotspot), more typical of grass or stubble burning, or a slow surface fire, than of a large crown fire.
- Burnt area
- 1,174ha
- GWIS perimeter (Copernicus)
- Duration
- 4days
- 8 Feb 2019 – 11 Feb 2019
- Municipalities hit
- 1
- municipalities
- Started on
- 8 Feb
- 2019
- Heat detections
- 42
- in a single hotspot: 16 MW
- Danger at start
- 5
- Very low · FWI index
- Average daily power
- 75MW
- detected power per day, on average
Where it burned
How it evolved, day by day
Fire radiative power detected each day, in megawatts, and number of hotspots. The magenta bar marks the peak day.
The weather it burned in
It had gone 11 days without rain (1 mm or more) when it started.
This area had burned before
55% of the perimeter overlaps earlier fires recorded since 2016: 651 ha in 2017.
What happened to each town
-
Vintar where it started1,181 ha2.2 %
Burnt area inside each municipality, from crossing the GWIS perimeter with administrative boundaries. The distance is from the town centre to the nearest fire: staying a kilometre away does not mean it reached the houses.
The weather day by day
ECMWF ERA5 reanalysis at the fire location, the standard reference for past weather, and the Canadian Fire Weather Index (the same system Copernicus uses), computed by WorldFires from that data. Days after the fire run until the first rain.
Open-Meteo.com (CC BY 4.0) · Copernicus Climate Change Service (ERA5)
| Day | High | Min. humidity | Peak gust | Rain | Danger (FWI) |
|---|---|---|---|---|---|
| 8 Feb | 24.8 °C | 65 % | 27 km/h | 0.0 mm | Very low 5 |
| 9 Feb | 25.6 °C | 65 % | 30 km/h | 0.0 mm | Low 6 |
| 10 Feb | 26.0 °C | 62 % | 35 km/h | 0.0 mm | Low 7 |
| 11 Feb | 26.1 °C | 62 % | 43 km/h | 0.0 mm | Low 8 |
| 12 Feb after | 26.2 °C | 57 % | 37 km/h | 0.0 mm | Low 8 |
| 13 Feb after | 27.1 °C | 57 % | 30 km/h | 0.0 mm | Low 8 |
| 14 Feb after | 25.6 °C | 58 % | 38 km/h | 0.0 mm | Low 9 |
| 15 Feb after | 25.6 °C | 58 % | 32 km/h | 0.0 mm | Low 8 |
| 16 Feb after | 25.3 °C | 61 % | 27 km/h | 0.0 mm | Low 7 |
| 17 Feb after | 24.9 °C | 71 % | 27 km/h | 0.5 mm | Low 6 |
| 18 Feb after | 25.7 °C | 67 % | 23 km/h | 0.0 mm | Low 6 |
| 19 Feb after | 26.7 °C | 60 % | 30 km/h | 0.0 mm | Low 7 |
| 20 Feb after | 26.5 °C | 62 % | 32 km/h | 0.0 mm | Low 7 |
| 21 Feb after | 25.1 °C | 67 % | 32 km/h | 0.8 mm | Very low 4 |
Before and after, from space
Drag the line to compare the same ground before the fire and after it.
If the day is cloudy, change the date: each satellite passes once a day. In false colour the burnt ground looks brown or red.
Detections table · 42Every satellite heat detection, one by one, with time, satellite, power and coordinates.
| Date and time | Satellite | FRP (MW) | Lat | Lon |
|---|
Other fires nearby
Frequently asked questions
- How long did the Vintar fire last?
- GWIS (Copernicus) dates it between 8 February 2019 and 11 February 2019: 4 days between the first and last heat detection of the perimeter.
- How much area did it burn?
- The perimeter GWIS (Copernicus) rebuilt from heat detections is 1,174 hectares (11.7 km²). It is an estimate: official national figures may differ.
- Which municipalities burned?
- The fire only entered Vintar (1,181 ha, 2.2 %).
- What was the weather like?
- During the fire the temperature reached 26.1 °C, humidity dropped to 62 % and gusts hit 43 km/h. The fire danger index (FWI) reached 8, class Low.
- Where does this data come from?
- From the GWIS (Copernicus) burnt perimeter, NASA FIRMS VIIRS hotspots and the administrative boundaries of Philippines (geoBoundaries). It is not an official report.
Where to verify it
A satellite detection is not an official report. Final figures and the fire’s status are published by each country’s emergency service.
Emergency number: 911
Satellite cross-check
Does something look wrong on this page?
This page is built from satellite data and official records, and it sometimes gets things wrong: the wrong dates, the wrong town, two fires merged into one, or something that was not a wildfire at all. If you know this fire first-hand (you live nearby, saw it, fought it or reported on it), tell us what really happened and we will check it.
Report an error
How we know this
- Perimeter: GWIS (Copernicus), rebuilt from heat detections rather than mapped on imagery.
- Dates from the perimeter: the VIIRS detections inside it did not change them. 42 Suomi-NPP VIIRS detections on those dates.
- We have not matched this page with any official record.
- Weather: Copernicus ERA5 reanalysis at the fire location, in cells of about 25 km.
Where this data comes from
The perimeter comes from the Copernicus Global Wildfire Information System (GWIS), which rebuilds it from MODIS and VIIRS heat detections and publishes it under CC BY 4.0. It is not measured on imagery as in Europe, so it is an estimate. Heat detections come from the VIIRS sensors aboard Suomi-NPP and NOAA-20, distributed by NASA FIRMS at 375 m resolution. Municipal boundaries come from geoBoundaries ADM3 (Creative Commons Attribution 3.0 Intergovernmental Organisations (CC BY 3.0 IGO)). The area per municipality is computed by WorldFires by crossing the perimeter with those boundaries, so it may differ from each country’s official figure.