Skip to content
worldfires
UY · Uruguay · →

Vergara fire, January 2023 Vergara

Out · last detection 16 Jan 2023, 18:00 UTC

The fire started on 15 January 2023 in Vergara, Uruguay, and satellites saw it burning for 2 days. Copernicus’s global GWIS system rebuilt a burnt perimeter of 1,312 hectares from heat detections, spread across a single municipality.

The largest in Uruguay in 2023, of 2.

The power measured by the satellite is low (22.8 MW in the strongest hotspot), more typical of grass or stubble burning, or a slow surface fire, than of a large crown fire.

Burnt area
1,312ha
GWIS perimeter (Copernicus)
Duration
2days
15 Jan 2023 – 16 Jan 2023
Municipalities hit
1
municipalities
Started on
15 Jan
2023
Heat detections
54
in a single hotspot: 23 MW
Danger at start
25
High · FWI index
Energy released
417MW
sum of detected power

Where it burned

16 Jan 2023
HOTSPOTS BY DAY 15 Jan16 Jan

How it evolved, day by day

1516

Fire radiative power detected each day, in megawatts, and number of hotspots. The magenta bar marks the peak day.

The weather it burned in

34°high
44km/h · peak gust
21%lowest humidity

It had gone 0 days without rain (1 mm or more) when it started. Rain came after the fire: 2.9 mm on 21 Jan.

This area had burned before

No earlier perimeters overlap this fire since 2016, when the satellite record begins.

What happened to each town

  1. Vergara where it started
    677 ha reached on 15 Jan
    2.1 %

Burnt area inside each municipality, from crossing the GWIS perimeter with administrative boundaries. The distance is from the town centre to the nearest fire: staying a kilometre away does not mean it reached the houses.

The weather day by day

ECMWF ERA5 reanalysis at the fire location, the standard reference for past weather, and the Canadian Fire Weather Index (the same system Copernicus uses), computed by WorldFires from that data. Days after the fire run until the first rain.

Open-Meteo.com (CC BY 4.0) · Copernicus Climate Change Service (ERA5)

Day High Min. humidity Peak gust Rain Danger (FWI)
14 Jan 31.5 °C 21 % 36 km/h 0.0 mm High 25
15 Jan 34.1 °C 21 % 39 km/h 0.0 mm High 33
16 Jan 34.1 °C 24 % 42 km/h 0.0 mm High 36
17 Jan after 31.7 °C 37 % 44 km/h 0.0 mm High 31
18 Jan after 30.2 °C 45 % 44 km/h 0.0 mm High 27
19 Jan after 29.7 °C 47 % 37 km/h 0.0 mm High 24
20 Jan after 32.0 °C 46 % 45 km/h 0.1 mm High 27
21 Jan after 32.2 °C 49 % 40 km/h 2.9 mm Low 9

Before and after, from space

Drag the line to compare the same ground before the fire and after it.

Before · 8 Jan 2023
After · 23 Jan 2023

If the day is cloudy, change the date: each satellite passes once a day. In false colour the burnt ground looks brown or red.

The smoke

CAMS · Copernicus

On 19 January 2023 the air beside the fire reached 7 µg/m³ of PM2.5, but no daily average passed the WHO guideline (15).

PM2.5 peak7 µg/m³
Days over the guideline0 days
PM1012 µg/m³
Optical depth0.22
13141516171819
Good Fair Moderate Poor Very poor Extremely poor

Particles from the Copernicus CAMS model at the centre of the perimeter; these are not measurements in each town. The pale bar is the worst hour, the solid one the daily average.

Open-Meteo.com (CC BY 4.0) · Copernicus Atmosphere Monitoring Service (CAMS)

Detections table · 54Every satellite heat detection, one by one, with time, satellite, power and coordinates.
⬇ Download CSV Times in UTC. Each detection is a 375 m pixel: a large fire yields hundreds per pass.
Date and timeSatelliteFRP (MW)LatLon

Frequently asked questions

How long did the Vergara fire last?
GWIS (Copernicus) dates it between 15 January 2023 and 16 January 2023: 2 days between the first and last heat detection of the perimeter.
How much area did it burn?
The perimeter GWIS (Copernicus) rebuilt from heat detections is 1,312 hectares (13.1 km²). It is an estimate: official national figures may differ.
Which municipalities burned?
The fire only entered Vergara (677 ha, 2.1 %).
What was the weather like?
During the fire the temperature reached 34.1 °C, humidity dropped to 21 % and gusts hit 44 km/h. The fire danger index (FWI) reached 36, class High.
Where does this data come from?
From the GWIS (Copernicus) burnt perimeter, NASA FIRMS VIIRS hotspots and the administrative boundaries of Uruguay (geoBoundaries). It is not an official report.

Where to verify it

A satellite detection is not an official report. Final figures and the fire’s status are published by each country’s emergency service.

Emergency number: 911 · 104

Satellite cross-check

Does something look wrong on this page?

This page is built from satellite data and official records, and it sometimes gets things wrong: the wrong dates, the wrong town, two fires merged into one, or something that was not a wildfire at all. If you know this fire first-hand (you live nearby, saw it, fought it or reported on it), tell us what really happened and we will check it.

Report an error
What do you think is wrong?

We will only use your email to reply about this report. Privacy. This is not an emergency service: if there is a fire now, call 911 · 104.

Where this data comes from

The perimeter comes from the Copernicus Global Wildfire Information System (GWIS), which rebuilds it from MODIS and VIIRS heat detections and publishes it under CC BY 4.0. It is not measured on imagery as in Europe, so it is an estimate. Heat detections come from the VIIRS sensors aboard Suomi-NPP and NOAA-20, distributed by NASA FIRMS at 375 m resolution. Municipal boundaries come from geoBoundaries ADM2 (Creative Commons Attribution-ShareAlike 3.0 Unported). The area per municipality is computed by WorldFires by crossing the perimeter with those boundaries, so it may differ from each country’s official figure.