Skip to content
worldfires
JP · Japan · →

Toyota fire, October 2026 豊田市 · Toyota

Out · last detection 12 Oct 2026, 03:45 UTC

The fire started on 6 October 2026 in Toyota, Japan, and satellites saw it burning for 7 days. Copernicus’s global GWIS system rebuilt a burnt perimeter of 232 hectares from heat detections, spread across a single municipality.

Number 49 in Japan in 2026, of 58.

The power measured by the satellite is low (5.7 MW in the strongest hotspot), more typical of grass or stubble burning, or a slow surface fire, than of a large crown fire.

Compare with…
Burnt area
232ha
GWIS perimeter (Copernicus)
Duration
7days
6 Oct 2026 – 12 Oct 2026
Municipalities hit
1
municipalities
Started on
6 Oct
2026
Heat detections
5
in a single hotspot: 6 MW
Danger at start
7
Low · FWI index
Average daily power
17MW
detected power per day, on average

Where it burned

HOTSPOTS BY DAY 6 Oct12 Oct
12 Oct 2026

How it evolved, day by day

6 Oct 2026 · 0 MW · 0 8 Oct 2026 · 0 MW · 0 10 Oct 2026 · 17 MW · 5 12 Oct 2026 · 0 MW · 0
6 Oct 8 Oct 10 Oct 12 Oct

Fire radiative power detected each day, in megawatts, and number of hotspots. The magenta bar marks the peak day.

The weather it burned in

27°high
50km/h · peak gust
46%lowest humidity

It had gone 5 days without rain (1 mm or more) when it started.

This area had burned before

No earlier perimeters overlap this fire since 2016, when the satellite record begins.

What happened to each town

  1. Toyota 豊田市 where it started
    232 ha reached on 6 Oct
    0.2 %

Burnt area inside each municipality, from crossing the GWIS perimeter with administrative boundaries. The distance runs from the point marking the centre of each area to the nearest fire: staying a kilometre away does not mean it reached the houses.

The weather day by day

ECMWF ERA5 reanalysis at the fire location, the standard reference for past weather, and the Canadian Fire Weather Index (the same system Copernicus uses), computed by WorldFires from that data. Days after the fire run until the first rain.

Open-Meteo.com (CC BY 4.0) · Copernicus Climate Change Service (ERA5)

Day High Min. humidity Peak gust Rain Danger (FWI)
6 Oct 26.6 °C 46 % 50 km/h 0.0 mm Low 7
7 Oct 24.9 °C 38 % 53 km/h 0.0 mm Low 10

Before and after, from space

Drag the line to compare the same ground before the fire and after it.

Before · 29 Sept 2026
After · 19 Oct 2026

If the day is cloudy, change the date: each satellite passes once a day. In false colour the burnt ground looks brown or red.

The smoke

CAMS · Copernicus

On 5 October 2026 the air beside the fire reached 32 µg/m³ of PM2.5. That day averaged 15: 1.0 times the WHO daily guideline (15).

PM2.5 peak32 µg/m³
Days over the guideline1 day
PM1032 µg/m³
Optical depth0.28
456
Good Fair Moderate Poor Very poor Extremely poor

Particles from the Copernicus CAMS model at the centre of the perimeter; these are not measurements in each town. The pale bar is the worst hour, the solid one the daily average.

Open-Meteo.com (CC BY 4.0) · Copernicus Atmosphere Monitoring Service (CAMS)

Detections table · 5Every satellite heat detection, one by one, with time, satellite, power and coordinates.
⬇ Download CSV Times in UTC. Each detection is a 375 m pixel: a large fire yields hundreds per pass.
Date and timeSatelliteFRP (MW)LatLon

Frequently asked questions

How long did the Toyota fire last?
GWIS (Copernicus) dates it between 6 October 2026 and 12 October 2026: 7 days between the first and last heat detection of the perimeter.
How much area did it burn?
The perimeter GWIS (Copernicus) rebuilt from heat detections is 232 hectares (2.3 km²). It is an estimate: official national figures may differ.
Which municipalities burned?
The fire only entered Toyota (232 ha, 0.2 %).
Is the Toyota fire still active?
No fire detections since 12 Oct 2026, 03:45 UTC. A lack of detections is not an official extinction.
What was the weather like?
During the fire the temperature reached 26.6 °C, humidity dropped to 46 % and gusts hit 50 km/h. The fire danger index (FWI) reached 7, class Low.
Where does this data come from?
From the GWIS (Copernicus) burnt perimeter, NASA FIRMS VIIRS hotspots and the administrative boundaries of Japan (geoBoundaries). It is not an official report.

Where to verify it

A satellite detection is not an official report. Final figures and the fire’s status are published by each country’s emergency service.

Emergency number: 119 · Emergency number and official warnings ›

Satellite cross-check

History of this page Changes in area, dates, name, official record or merged pages, compared every night since 24 October 2026.

No changes since 24 October 2026.

RSS Changes to this page

Does something look wrong on this page?

This page is built from satellite data and official records, and it sometimes gets things wrong: the wrong dates, the wrong town, two fires merged into one, or something that was not a wildfire at all. If you know this fire first-hand (you live nearby, saw it, fought it or reported on it), tell us what really happened and we will check it.

Report an error
What do you think is wrong?

We will only use your email to reply about this report. Privacy. This is not an emergency service: if there is a fire now, call 119.

How we know this
  • Perimeter: GWIS (Copernicus), rebuilt from heat detections rather than mapped on imagery.
  • Dates from the perimeter: the VIIRS detections inside it did not change them. 5 Suomi-NPP VIIRS detections on those dates.
  • We have not matched this page with any official record.
  • Weather: Copernicus ERA5 reanalysis at the fire location, in cells of about 25 km.

How we build fire pages: methodology ›

Where this data comes from

The perimeter comes from the Copernicus Global Wildfire Information System (GWIS), which rebuilds it from MODIS and VIIRS heat detections and publishes it under CC BY 4.0. It is not measured on imagery as in Europe, so it is an estimate. Heat detections come from the VIIRS sensors aboard Suomi-NPP and NOAA-20, distributed by NASA FIRMS at 375 m resolution. Municipal boundaries come from geoBoundaries ADM2 (Creative Commons Attribution-ShareAlike 2.0). The area per municipality is computed by WorldFires by crossing the perimeter with those boundaries, so it may differ from each country’s official figure.