Skip to content
worldfires
en
PE · Peru · →

Talara fire, September 2019 Talara

Out · last measured on 18 Sept 2019

The fire started on 18 September 2019 in Talara, Peru, and satellites saw it burning for 1 day. Copernicus’s global GWIS system rebuilt a burnt perimeter of 3,493 hectares from heat detections, spread across a single municipality.

It is the 2th largest in Piura since 2016 (of 13 with a page). Number 4 in Peru in 2019, of 47.

Compare with…

Suggestions: Contralmirante Villar · 2019

We have the GWIS perimeter for this fire, but the VIIRS sensors did not capture it in enough detail: no day-by-day evolution, but the split by municipality is there.

Burnt area
3,493ha
GWIS perimeter (Copernicus)
Duration
1day
18 Sept 2019 – 18 Sept 2019
Municipalities hit
1
provinces
Started on
18 Sept
2019
Danger at start
18
Moderate · FWI index

Where it burned

The weather it burned in

26°high
36km/h · peak gust
61%lowest humidity

It had gone more than two months without rain (1 mm or more) when it started. Rain came after the fire: 3.1 mm on 24 Sept.

This area had burned before

No earlier perimeters overlap this fire since 2016, when the satellite record begins.

How big is it?

10 km
It burned the equivalent of 2.2% of the area of London (35 km² against 1,583 km²).

London boundary: geoBoundaries · Office for National Statistics (Open Government Licence v3.0).

This compares size, not location: both shapes are at the same scale, north up, centred on each other.

What happened to each town

  1. Talara 99,651 inhabitants where it started
    3,515 ha
    1.2 %

Burnt area inside each municipality, from crossing the GWIS perimeter with administrative boundaries. The distance runs from the point marking the centre of each area to the nearest fire: staying a kilometre away does not mean it reached the houses.

People and buildings inside the perimeter

GHSL 2020
Built-up area< 0.1 ha
Residents< 20

Inside the perimeter there was no noticeable built-up land and almost nobody lived there (GHSL 2020, satellite-based estimate).

This is an estimate on 100 m cells, made from satellite imagery and census data: it does not mean that homes burned or that anyone was harmed. The perimeter also contains land that never burned.

Source: Global Human Settlement Layer (GHS-BUILT-S and GHS-POP R2023A), European Commission Joint Research Centre (JRC), © European Union, CC BY 4.0. Sum inside the perimeter computed by WorldFires. human-settlement.emergency.copernicus.eu

The weather day by day

ECMWF ERA5 reanalysis at the fire location, the standard reference for past weather, and the Canadian Fire Weather Index (the same system Copernicus uses), computed by WorldFires from that data. Days after the fire run until the first rain.

Open-Meteo.com (CC BY 4.0) · Copernicus Climate Change Service (ERA5)

Day High Min. humidity Peak gust Rain Danger (FWI)
18 Sept 25.5 °C 61 % 36 km/h 0.0 mm Moderate 18
19 Sept after 27.5 °C 55 % 42 km/h 0.0 mm High 22
20 Sept after 25.6 °C 55 % 32 km/h 0.0 mm Moderate 19
21 Sept after 28.0 °C 54 % 34 km/h 0.0 mm Moderate 19
22 Sept after 26.3 °C 57 % 35 km/h 0.0 mm Moderate 20
23 Sept after 26.0 °C 58 % 34 km/h 0.0 mm Moderate 20
24 Sept after 27.0 °C 60 % 36 km/h 3.1 mm Low 6

Before and after, from space

Drag the line to compare the same ground before the fire and after it.

Before · 11 Sept 2019
After · 25 Sept 2019

If the day is cloudy, change the date: each satellite passes once a day. In false colour the burnt ground looks brown or red.

Other fires nearby

All fires in Peru ›

Frequently asked questions

How long did the Talara fire last?
GWIS (Copernicus) dates it between 18 September 2019 and 18 September 2019: 1 day between the first and last heat detection of the perimeter.
How much area did it burn?
The perimeter GWIS (Copernicus) rebuilt from heat detections is 3,493 hectares (34.9 km²). It is an estimate: official national figures may differ.
Which municipalities burned?
The fire only entered Talara (3,515 ha, 1.2 %).
What was the weather like?
During the fire the temperature reached 25.5 °C, humidity dropped to 61 % and gusts hit 36 km/h. The fire danger index (FWI) reached 18, class Moderate.
Where does this data come from?
From the GWIS (Copernicus) burnt perimeter, NASA FIRMS VIIRS hotspots and the administrative boundaries of Peru (geoBoundaries). It is not an official report.

Where to verify it

A satellite detection is not an official report. Final figures and the fire’s status are published by each country’s emergency service.

Emergency number: 116 · 105 · Emergency number and official warnings ›

Satellite cross-check

History of this page Changes in area, dates, name, official record or merged pages, compared every night since 24 October 2026.

No changes since 24 October 2026.

RSS Changes to this page

Does something look wrong on this page?

This page is built from satellite data and official records, and it sometimes gets things wrong: the wrong dates, the wrong town, two fires merged into one, or something that was not a wildfire at all. If you know this fire first-hand (you live nearby, saw it, fought it or reported on it), tell us what really happened and we will check it.

Report an error
What do you think is wrong?

We will only use your email to reply about this report. Privacy. This is not an emergency service: if there is a fire now, call 116 · 105.

How we know this
  • Perimeter: GWIS (Copernicus), rebuilt from heat detections rather than mapped on imagery.
  • Dates from the perimeter: the VIIRS detections inside it did not change them. No Suomi-NPP VIIRS detections on those dates.
  • We have not matched this page with any official record.
  • Weather: Copernicus ERA5 reanalysis at the fire location, in cells of about 25 km.
  • Built-up area and population come from the JRC Global Human Settlement Layer (epoch 2020, 100 m cells), summed inside the perimeter: an estimate of what was there, not a damage count.

How we build fire pages: methodology ›

Where this data comes from

The perimeter comes from the Copernicus Global Wildfire Information System (GWIS), which rebuilds it from MODIS and VIIRS heat detections and publishes it under CC BY 4.0. It is not measured on imagery as in Europe, so it is an estimate. Heat detections come from the VIIRS sensors aboard Suomi-NPP and NOAA-20, distributed by NASA FIRMS at 375 m resolution. Municipal boundaries come from geoBoundaries ADM2 (Creative Commons Attribution 3.0 Intergovernmental Organisations (CC BY 3.0 IGO)). The area per municipality is computed by WorldFires by crossing the perimeter with those boundaries, so it may differ from each country’s official figure.