Skip to content
worldfires
US · United States · →

Summit Fire, July 2026 Los Angeles

Out · last measured on 10 Jul 2026

The fire started on 10 July 2026 in Los Angeles, United States, and satellites saw it burning for 1 day. United States agencies (MTBS / NIFC) mapped an official burnt perimeter of 1,089 hectares, spread across a single county.

It is the 273th largest in California since 2016 (of 442 with a page). Number 252 in United States in 2026, of 423.

We have the official perimeter (MTBS / NIFC) for this fire, but not yet its hotspots: NASA publishes the yearly hotspot archive only once the year closes. The page picks them up automatically when they are available.

Burnt area
1,089ha
official perimeter (MTBS / NIFC)
Duration
1day
10 Jul 2026 – 10 Jul 2026
Municipalities hit
1
counties
Started on
10 Jul
2026
Danger at start
20
Moderate · FWI index

Where it burned

The weather it burned in

34°high
12km/h · peak gust
11%lowest humidity

It had gone 2 days without rain (1 mm or more) when it started. Rain came after the fire: 1.8 mm on 13 Jul.

This area had burned before

4% of the perimeter overlaps earlier fires recorded since 2016: 43 ha in 2024.

What happened to each town

  1. Los Angeles where it started
    1,103 ha
    0.1 %

Burnt area inside each county, from crossing the official perimeter with administrative boundaries. The distance is from the town centre to the nearest fire: staying a kilometre away does not mean it reached the houses.

The weather day by day

ECMWF ERA5 reanalysis at the fire location, the standard reference for past weather, and the Canadian Fire Weather Index (the same system Copernicus uses), computed by WorldFires from that data. Days after the fire run until the first rain.

Open-Meteo.com (CC BY 4.0) · Copernicus Climate Change Service (ERA5)

Day High Min. humidity Peak gust Rain Danger (FWI)
10 Jul 33.8 °C 11 % 12 km/h 0.0 mm Moderate 20
11 Jul after 33.3 °C 8 % 20 km/h 0.0 mm High 28
12 Jul after 28.9 °C 19 % 12 km/h 0.2 mm Moderate 21
13 Jul after 27.8 °C 34 % 13 km/h 1.8 mm Low 8

Before and after, from space

Drag the line to compare the same ground before the fire and after it.

Before · 3 Jul 2026
After · 17 Jul 2026

If the day is cloudy, change the date: each satellite passes once a day. In false colour the burnt ground looks brown or red.

The smoke

CAMS · Copernicus

On 12 July 2026 the air beside the fire reached 28 µg/m³ of PM2.5. That day averaged 20: 1.3 times the WHO daily guideline (15).

PM2.5 peak28 µg/m³
Days over the guideline4 days
PM1033 µg/m³
Optical depth0.27
8910111213
Good Fair Moderate Poor Very poor Extremely poor

Particles from the Copernicus CAMS model at the centre of the perimeter; these are not measurements in each town. The pale bar is the worst hour, the solid one the daily average.

Open-Meteo.com (CC BY 4.0) · Copernicus Atmosphere Monitoring Service (CAMS)

Other fires nearby

All fires in United States ›

Frequently asked questions

How long did the Summit fire last?
It burned between 10 July 2026 and 10 July 2026: 1 day, according to the start date recorded by United States agencies (MTBS / NIFC) and the heat detections seen by satellite.
How much area did it burn?
The official perimeter published by United States agencies (MTBS / NIFC) is 1,089 hectares (10.9 km²). Other tallies, such as daily incident reports, may give slightly different figures.
Which counties burned?
The fire only entered Los Angeles (1,103 ha, 0.1 %).
What was the weather like?
During the fire the temperature reached 33.8 °C, humidity dropped to 11 % and gusts hit 12 km/h. The fire danger index (FWI) reached 20, class Moderate.
Where does this data come from?
From the official burnt perimeter of United States agencies (MTBS / NIFC, public domain), NASA FIRMS VIIRS hotspots and the administrative boundaries of United States. It is not an official report.

Where to verify it

A satellite detection is not an official report. Final figures and the fire’s status are published by each country’s emergency service.

Emergency number: 911

Satellite cross-check

Does something look wrong on this page?

This page is built from satellite data and official records, and it sometimes gets things wrong: the wrong dates, the wrong town, two fires merged into one, or something that was not a wildfire at all. If you know this fire first-hand (you live nearby, saw it, fought it or reported on it), tell us what really happened and we will check it.

Report an error
What do you think is wrong?

We will only use your email to reply about this report. Privacy. This is not an emergency service: if there is a fire now, call 911.

Where this data comes from

The perimeter is official and in the public domain. For past years it comes from MTBS (Monitoring Trends in Burn Severity), run by the U.S. Geological Survey and the USDA Forest Service, which map it on Landsat and Sentinel-2 imagery. For the current and last year it comes from WFIGS at the National Interagency Fire Center (NIFC): incident perimeters mapped by fire crews, aircraft and imagery. Heat detections come from the VIIRS sensors aboard Suomi-NPP and NOAA-20, distributed by NASA FIRMS at 375 m resolution. County boundaries come from geoBoundaries ADM2 (Public Domain). The area per county is computed by WorldFires by crossing the perimeter with those boundaries, so it may differ slightly from official figures.