Skip to content
worldfires
AU · Australia · –

Snowy Monaro fire, 23 January 2020 Bega Valley, Snowy Monaro

Out · last detection

The fire started on in Snowy Monaro, Australia, and satellites saw it burning for 16 days. Copernicus’s global GWIS system rebuilt a burnt perimeter of 48,535 hectares from heat detections, spread across 2 municipalities.

It is number 22 by size of the 121 fires with a page that started in New South Wales since 2016. Number 4 in Australia in 2020, of 67.

Burnt area
48,535ha
GWIS perimeter (Copernicus)
Duration
16days
23 Jan 2020 – 7 Feb 2020
Municipalities hit
2
local government areas
Started on
23 Jan
2020
Heat detections
4,437
in a single hotspot: 1,216 MW
Danger at start
27
High · FWI index
Average daily power
6.2GW
detected power per day, on average

Where it burned

HOTSPOTS BY DAY 23 Jan7 Feb
7 Feb 2020

How it evolved, day by day

23 Jan 2020 · 192 MW · 85 24 Jan 2020 · 1,172 MW · 53 25 Jan 2020 · 529 MW · 53 26 Jan 2020 · 4,938 MW · 134 27 Jan 2020 · 853 MW · 48 28 Jan 2020 · 304 MW · 80 29 Jan 2020 · 997 MW · 137 30 Jan 2020 · 6,495 MW · 308 31 Jan 2020 · 18,342 MW · 576 1 Feb 2020 · 53,372 MW · 2139 3 Feb 2020 · 425 MW · 146 4 Feb 2020 · 2,757 MW · 406 5 Feb 2020 · 2,850 MW · 217 6 Feb 2020 · 17 MW · 16 7 Feb 2020 · 163 MW · 39
23 Jan 26 Jan 29 Jan 1 Feb 5 Feb

Fire radiative power detected each day, in megawatts, and number of hotspots. The magenta bar marks the peak day.

The weather it burned in

37°high
70km/h · peak gust
24%lowest humidity

It had gone one day without rain (1 mm or more) when it started. Rain came after the fire: 27.9 mm on 8 Feb.

This area had burned before

4% of the perimeter overlaps earlier fires recorded since 2016: 1,142 ha in 2016, 584 ha in 2019.

How big is it?

10 km
It burned the equivalent of 31% of the area of London (485 km² against 1,583 km²).

London boundary: geoBoundaries · Office for National Statistics (Open Government Licence v3.0).

This compares size, not location: both shapes are at the same scale, north up, centred on each other.

What happened to each town

  1. 36,570 ha
    5.8 %
  2. Snowy Monaro where it started
    12,128 ha
    0.8 %

Burnt area inside each municipality, from crossing the GWIS perimeter with administrative boundaries. The distance runs from the point marking the centre of each area to the nearest fire: staying a kilometre away does not mean it reached the houses.

People and buildings inside the perimeter

GHSL 2020
Built-up area16 ha
Residents≈ 350

Inside the perimeter there were about 16 hectares of built-up land and about 350 residents (GHSL 2020, satellite-based estimate).

This is an estimate on 100 m cells, made from satellite imagery and census data: it does not mean that homes burned or that anyone was harmed. The perimeter also contains land that never burned.

Source: Global Human Settlement Layer (GHS-BUILT-S and GHS-POP R2023A), European Commission Joint Research Centre (JRC), © European Union, CC BY 4.0. Sum inside the perimeter computed by WorldFires. human-settlement.emergency.copernicus.eu

The weather day by day

ECMWF ERA5 reanalysis at the fire location, the standard reference for past weather, and the Canadian Fire Weather Index (the same system Copernicus uses), computed by WorldFires from that data. Days after the fire run until the first rain.

Open-Meteo.com (CC BY 4.0) · Copernicus Climate Change Service (ERA5)

Started with Strong wind: 39 % of the area in Australia

Day High Min. humidity Peak gust Rain Danger (FWI)
23 Jan 30.2 °C 24 % 62 km/h 0.0 mm High 27
24 Jan 20.7 °C 44 % 46 km/h 7.5 mm Very low 1
25 Jan 24.2 °C 48 % 44 km/h 4.9 mm Very low 1
26 Jan 29.1 °C 29 % 44 km/h 1.4 mm Very low 2
27 Jan 27.3 °C 40 % 48 km/h 0.0 mm Low 6
28 Jan 23.2 °C 56 % 42 km/h 0.0 mm Low 8
29 Jan 25.7 °C 38 % 41 km/h 0.0 mm Low 10
30 Jan 31.6 °C 27 % 35 km/h 0.0 mm Moderate 17
31 Jan 35.7 °C 26 % 29 km/h 0.0 mm Moderate 18
1 Feb 36.7 °C 27 % 44 km/h 0.2 mm High 28
2 Feb 23.2 °C 66 % 44 km/h 3.2 mm Low 10
3 Feb 18.1 °C 46 % 70 km/h 2.1 mm Very low 1
4 Feb 18.6 °C 36 % 39 km/h 0.0 mm Low 6
5 Feb 22.4 °C 41 % 45 km/h 0.0 mm Low 11
6 Feb 22.4 °C 54 % 41 km/h 0.8 mm Moderate 15
7 Feb 21.4 °C 57 % 39 km/h 2.5 mm Low 9
8 Feb after 18.0 °C 85 % 43 km/h 27.9 mm Very low 0

Its twins: fires that started in the same weather

It started with an FWI of 27.1, a minimum humidity of 24% and 1 day without rain. Fires in the area that started in weather like this since 2016: 9.

FWI at the start 27.1
Minimum humidity 24 %
Days without rain 1
this fire chosen twins rest of the area
Almost identicalSimilar

Outlines of the closest twins

Shoalhaven fire, December 2019
143,634 ha 28 days FWI 25.5 Min. humidity 26 % 222 km away, in 2019

First rain (1 mm or more) after it ended: 10.7 mm on 16 Jan.

What happened to them

Fires in the area that started in similar weather: 9. With fewer than 15 we give no figures: they would be more noise than signal.

This is a bank of analogues: it shows what usually happens, not what will happen. With fewer than 15 twins we give no figures. How we calculate it

How it ended

27.9 mmfirst rain
8 Febthe day after it ended
70km/h · max. gust

It was considered over on 7 Feb, and on 8 Feb 27.9 mm fell. We do not know whether the rain or the firefighters put it out.

Weather on this page: Open-Meteo.com (CC BY 4.0) · Copernicus Climate Change Service (ERA5)

How a twin is chosen

  • Same area: fires that have already ended, less than 250 km from this one, since 2016.
  • Same start: we compare the FWI on the first day, the minimum humidity that day and the run of days without rain before it. The slider sets how much they may differ.
  • Only pages with final weather data (ERA5 reanalysis) calculated in the same way as this fire’s; agricultural and grass burns and pages with data under review are left out.
  • Fires burning at the same time as this one (a week before or after) are left out: they share the same spell of weather and do not count as a precedent.
  • They are sorted by similarity, and the outlines of the first five are drawn.

How we calculate it

Before and after, from space

Drag the line to compare the same ground before the fire and after it.

Before · 16 Jan 2020
After · 14 Feb 2020

If the day is cloudy, change the date: each satellite passes once a day. In false colour the burnt ground looks brown or red.

Detections table · 4,437Every satellite heat detection, one by one, with time, satellite, power and coordinates.
⬇ Download CSV Times in UTC. Each detection is a 375 m pixel: a large fire yields hundreds per pass.
Date and timeSatelliteFRP (MW)LatLon

Other fires nearby

All fires in Australia

Frequently asked questions

How long did the Snowy Monaro fire last?
GWIS (Copernicus) dates it between 23 January 2020 and 7 February 2020: 16 days between the first and last heat detection of the perimeter.
How much area did it burn?
The perimeter GWIS (Copernicus) rebuilt from heat detections is 48,535 hectares (485.4 km²). It is an estimate: official national figures may differ.
Which municipalities burned?
The fire entered 2 municipalities: Bega Valley (36,570 ha, 5.8 %); Snowy Monaro (12,128 ha, 0.8 %).
What was the weather like?
During the fire the temperature reached 36.7 °C, humidity dropped to 24 % and gusts hit 70 km/h. The fire danger index (FWI) reached 28, class High.
Where does this data come from?
From the GWIS (Copernicus) burnt perimeter, NASA FIRMS VIIRS hotspots and the administrative boundaries of Australia (geoBoundaries). It is not an official report.

Where to verify it

A satellite detection is not an official report. Final figures and the fire’s status are published by each country’s emergency service.

Emergency number: 000 · Emergency number and official warnings

Satellite cross-check

History of this page Changes in area, dates, name, official record or merged pages, compared every night since 24 October 2026.

Does something look wrong on this page?

This page is built from satellite data and official records, and it sometimes gets things wrong: the wrong dates, the wrong town, two fires merged into one, or something that was not a wildfire at all. If you know this fire first-hand (you live nearby, saw it, fought it or reported on it), tell us what really happened and we will check it.

Report an error
What do you think is wrong?

We will only use your email to reply about this report. Privacy. This is not an emergency service: if there is a fire now, call 000.

How we know this
  • Perimeter: GWIS (Copernicus), rebuilt from heat detections rather than mapped on imagery.
  • Dates from the perimeter: the VIIRS detections inside it did not change them. 4,437 Suomi-NPP VIIRS detections on those dates.
  • We have not matched this page with any official record.
  • Weather: Copernicus ERA5 reanalysis at the fire location, in cells of about 25 km.
  • Built-up area and population come from the JRC Global Human Settlement Layer (epoch 2020, 100 m cells), summed inside the perimeter: an estimate of what was there, not a damage count.

How we build fire pages: methodology

Where this data comes from

The perimeter comes from the Copernicus Global Wildfire Information System (GWIS), which rebuilds it from MODIS and VIIRS heat detections and publishes it under CC BY 4.0. It is not measured on imagery as in Europe, so it is an estimate. Heat detections come from the VIIRS sensors aboard Suomi-NPP and NOAA-20, distributed by NASA FIRMS at 375 m resolution. Municipal boundaries come from geoBoundaries ADM2 (Creative Commons Attribution 4.0 International (CC BY 4.0)). The area per municipality is computed by WorldFires by crossing the perimeter with those boundaries, so it may differ from each country’s official figure.