Skip to content
worldfires
PY · Paraguay · –

San Lazaro fire, 21 September 2019 San Lazaro

Out · last detection 1 Oct 2019, 04:50 UTC

The fire started on 21 September 2019 in San Lazaro, Paraguay, and satellites saw it burning for 11 days. Copernicus’s global GWIS system rebuilt a burnt perimeter of 2,060 hectares from heat detections, spread across a single municipality.

It is the 109th largest in Concepción since 2016 (of 191 with a page). Number 136 in Paraguay in 2019, of 229.

The power measured by the satellite is low (10.8 MW in the strongest hotspot), more typical of grass or stubble burning, or a slow surface fire, than of a large crown fire.

Burnt area
2,060ha
GWIS perimeter (Copernicus)
Duration
11days
21 Sept 2019 – 1 Oct 2019
Municipalities hit
1
districts
Started on
21 Sept
2019
Heat detections
26
in a single hotspot: 11 MW
Danger at start
11
Moderate · FWI index
Average daily power
13MW
detected power per day, on average

Where it burned

HOTSPOTS BY DAY 21 Sept1 Oct
1 Oct 2019

How it evolved, day by day

22 Sept 2019 · 21 MW · 3 23 Sept 2019 · 7 MW · 3 24 Sept 2019 · 3 MW · 2 25 Sept 2019 · 3 MW · 1 28 Sept 2019 · 24 MW · 4 29 Sept 2019 · 37 MW · 9 30 Sept 2019 · 3 MW · 2 1 Oct 2019 · 10 MW · 2
22 Sept 24 Sept 29 Sept

Fire radiative power detected each day, in megawatts, and number of hotspots. The magenta bar marks the peak day.

The weather it burned in

39°high
72km/h · peak gust
23%lowest humidity

It had gone 0 days without rain (1 mm or more) when it started. Rain came after the fire: 13.6 mm on 5 Oct.

This area had burned before

34% of the perimeter overlaps earlier fires recorded since 2016: 630 ha in 2016, 497 ha in 2018. Part of it burned more than once, so the yearly figures add up to more than the 702 ha that had burned before.

How big is it?

10 km
It burned the equivalent of 1.3% of the area of London (21 km² against 1,583 km²).

London boundary: geoBoundaries · Office for National Statistics (Open Government Licence v3.0).

This compares size, not location: both shapes are at the same scale, north up, centred on each other.

What happened to each town

  1. San Lazaro where it started
    2,069 ha reached on 22 Sept
    1.7 %

Burnt area inside each municipality, from crossing the GWIS perimeter with administrative boundaries. The distance runs from the point marking the centre of each area to the nearest fire: staying a kilometre away does not mean it reached the houses.

People and buildings inside the perimeter

GHSL 2020
Built-up area< 0.1 ha
Residents< 20

Inside the perimeter there was no noticeable built-up land and almost nobody lived there (GHSL 2020, satellite-based estimate).

This is an estimate on 100 m cells, made from satellite imagery and census data: it does not mean that homes burned or that anyone was harmed. The perimeter also contains land that never burned.

Source: Global Human Settlement Layer (GHS-BUILT-S and GHS-POP R2023A), European Commission Joint Research Centre (JRC), © European Union, CC BY 4.0. Sum inside the perimeter computed by WorldFires. human-settlement.emergency.copernicus.eu

The weather day by day

ECMWF ERA5 reanalysis at the fire location, the standard reference for past weather, and the Canadian Fire Weather Index (the same system Copernicus uses), computed by WorldFires from that data. Days after the fire run until the first rain.

Open-Meteo.com (CC BY 4.0) · Copernicus Climate Change Service (ERA5)

Day High Min. humidity Peak gust Rain Danger (FWI)
21 Sept 30.4 °C 44 % 34 km/h 0.0 mm Moderate 11
22 Sept 33.5 °C 32 % 36 km/h 0.0 mm High 22
23 Sept 34.6 °C 32 % 32 km/h 0.0 mm High 22
24 Sept 35.7 °C 30 % 29 km/h 0.0 mm Moderate 21
25 Sept 26.6 °C 55 % 28 km/h 16.0 mm Very low 0
26 Sept 31.1 °C 46 % 20 km/h 0.1 mm Very low 1
27 Sept 33.6 °C 23 % 25 km/h 0.0 mm Moderate 12
28 Sept 35.5 °C 29 % 30 km/h 0.0 mm Moderate 19
29 Sept 38.3 °C 27 % 31 km/h 0.0 mm High 24
30 Sept 38.1 °C 32 % 57 km/h 0.0 mm High 38
1 Oct 38.9 °C 32 % 72 km/h 0.0 mm Very high 47
2 Oct after 32.5 °C 42 % 56 km/h 0.1 mm High 36
3 Oct after 31.9 °C 48 % 26 km/h 0.0 mm Moderate 15
4 Oct after 36.1 °C 40 % 31 km/h 0.0 mm Moderate 16
5 Oct after 27.4 °C 60 % 36 km/h 13.6 mm Very low 0

Its twins: fires that started in the same weather

It started with an FWI of 11.3, a minimum humidity of 44% and rain the day before. Fires in the area that started in weather like this since 2016: 32.

FWI at the start 11.3
Minimum humidity 44 %
Days without rain 0
this fire chosen twins rest of the area
Almost identicalSimilar

Outlines of the closest twins

Villa Hayes fire, October 2017
1,737 ha 3 days FWI 11.0 Min. humidity 44 % 171 km away, in 2017

First rain (1 mm or more) after it ended: 4.2 mm on 27 Oct.

What happened to them

7 days
median duration
2,282 ha
median area
100 %
went past 1,000 ha
5.0 mm
rain at the end (median; 29 of 32 had it)

It burned an area similar to its twins (2,060 ha against a median of 2,282 ha) and lasted 11 days, against 7 days.

In 3 of 32, not even 1 mm fell in the ten days after the end: they went out without rain. In the rest, the first rainy day brought a median of 5.0 mm.

This is a bank of analogues: it shows what usually happens, not what will happen. With fewer than 15 twins we give no figures. How we calculate it

How it ended

13.6 mmfirst rain
5 Oct4 days after it ended
72km/h · max. gust

It was considered over on 1 Oct, and on 5 Oct 13.6 mm fell. We do not know whether the rain or the firefighters put it out. Twins with rain when they ended: 29 of 32, with a median of 5.0 mm.

Weather on this page: Open-Meteo.com (CC BY 4.0) · Copernicus Climate Change Service (ERA5)

How a twin is chosen

  • Same area: fires that have already ended, less than 250 km from this one, since 2016.
  • Same start: we compare the FWI on the first day, the minimum humidity that day and the run of days without rain before it. The slider sets how much they may differ.
  • Only pages with final weather data (ERA5 reanalysis) calculated in the same way as this fire’s; agricultural and grass burns and pages with data under review are left out.
  • Fires burning at the same time as this one (a week before or after) are left out: they share the same spell of weather and do not count as a precedent.
  • They are sorted by similarity, and the outlines of the first five are drawn.

How we calculate it

Before and after, from space

Drag the line to compare the same ground before the fire and after it.

Before · 14 Sept 2019
After · 8 Oct 2019

If the day is cloudy, change the date: each satellite passes once a day. In false colour the burnt ground looks brown or red.

Detections table · 26Every satellite heat detection, one by one, with time, satellite, power and coordinates.
⬇ Download CSV Times in UTC. Each detection is a 375 m pixel: a large fire yields hundreds per pass.
Date and timeSatelliteFRP (MW)LatLon

Other fires nearby

All fires in Paraguay

Frequently asked questions

How long did the San Lazaro fire last?
According to the heat detections seen by satellite inside the perimeter, it burned from 21 September 2019 to 1 October 2019 (11 days). The perimeter dates it from 21 September 2019 to 25 September 2019.
How much area did it burn?
The perimeter GWIS (Copernicus) rebuilt from heat detections is 2,060 hectares (20.6 km²). It is an estimate: official national figures may differ.
Which municipalities burned?
The fire only entered San Lazaro (2,069 ha, 1.7 %).
What was the weather like?
During the fire the temperature reached 38.9 °C, humidity dropped to 23 % and gusts hit 72 km/h. The fire danger index (FWI) reached 47, class Very high.
Where does this data come from?
From the GWIS (Copernicus) burnt perimeter, NASA FIRMS VIIRS hotspots and the administrative boundaries of Paraguay (geoBoundaries). It is not an official report.
How did the fires that started in similar weather in this area end?
Fires less than 250 km away that started since 2016 with a similar FWI, humidity and dry spell: 32. Their median duration was 7 days and their median area 2,282 ha; 100 % went past 1,000 ha. In 3 of 32, not even 1 mm fell in the ten days after the end: they went out without rain. In the rest, the first rainy day brought a median of 5.0 mm.

Where to verify it

A satellite detection is not an official report. Final figures and the fire’s status are published by each country’s emergency service.

Emergency number: 132 · 911 · Emergency number and official warnings

Satellite cross-check

History of this page · 1 Changes in area, dates, name, official record or merged pages, compared every night since 24 October 2026.
  1. Last day with fire: 25 September 2019 → 1 October 2019.

RSS Changes to this page With cross-checks and a citable version

Does something look wrong on this page?

This page is built from satellite data and official records, and it sometimes gets things wrong: the wrong dates, the wrong town, two fires merged into one, or something that was not a wildfire at all. If you know this fire first-hand (you live nearby, saw it, fought it or reported on it), tell us what really happened and we will check it.

Report an error
What do you think is wrong?

We will only use your email to reply about this report. Privacy. This is not an emergency service: if there is a fire now, call 132 · 911.

How we know this
  • Perimeter: GWIS (Copernicus), rebuilt from heat detections rather than mapped on imagery.
  • Dates adjusted with the VIIRS detections inside the perimeter, which said 21 September 2019 to 25 September 2019. 26 Suomi-NPP VIIRS detections on those dates.
  • We have not matched this page with any official record.
  • Weather: Copernicus ERA5 reanalysis at the fire location, in cells of about 25 km.
  • Built-up area and population come from the JRC Global Human Settlement Layer (epoch 2020, 100 m cells), summed inside the perimeter: an estimate of what was there, not a damage count.

How we build fire pages: methodology

Where this data comes from

The perimeter comes from the Copernicus Global Wildfire Information System (GWIS), which rebuilds it from MODIS and VIIRS heat detections and publishes it under CC BY 4.0. It is not measured on imagery as in Europe, so it is an estimate. Heat detections come from the VIIRS sensors aboard Suomi-NPP and NOAA-20, distributed by NASA FIRMS at 375 m resolution. Municipal boundaries come from geoBoundaries ADM2 (Creative Commons Attribution 4.0 (CC BY 4.0)). The area per municipality is computed by WorldFires by crossing the perimeter with those boundaries, so it may differ from each country’s official figure.