Skip to content
worldfires
MW · Malawi · →

Rumphi fire, 2 August 2026 Rumphi

Out · last detection 2 Aug 2026, 12:08 UTC

The fire started on 2 August 2026 in Rumphi, Malawi, and satellites saw it burning for 1 day. Copernicus’s global GWIS system rebuilt a burnt perimeter of 1,253 hectares from heat detections, spread across a single municipality.

It is the 273th largest in Northern Region since 2016 (of 418 with a page). Number 60 in Malawi in 2026, of 91.

The power measured by the satellite is low (23.2 MW in the strongest hotspot), more typical of grass or stubble burning, or a slow surface fire, than of a large crown fire.

Burnt area
1,253ha
GWIS perimeter (Copernicus)
Duration
1day
2 Aug 2026 – 2 Aug 2026
Municipalities hit
1
districts
Started on
2 Aug
2026
Heat detections
27
in a single hotspot: 23 MW
Danger at start
26
High · FWI index
Energy released
317MW
sum of detected power

Where it burned

HOTSPOTS BY DAY 2 Aug2 Aug

How it evolved, day by day

2

Fire radiative power detected each day, in megawatts, and number of hotspots. The magenta bar marks the peak day.

The weather it burned in

22°high
27km/h · peak gust
31%lowest humidity

It had gone 57 days without rain (1 mm or more) when it started.

This area had burned before

71% of the perimeter overlaps earlier fires recorded since 2016: 445 ha in 2016, 663 ha in 2024, 90 ha in 2025. Part of it burned more than once, so the yearly figures add up to more than the 886 ha that had burned before.

What happened to each town

  1. Rumphi where it started
    1,261 ha reached on 2 Aug
    0.3 %

Burnt area inside each municipality, from crossing the GWIS perimeter with administrative boundaries. The distance is from the town centre to the nearest fire: staying a kilometre away does not mean it reached the houses.

The weather day by day

ECMWF ERA5 reanalysis at the fire location, the standard reference for past weather, and the Canadian Fire Weather Index (the same system Copernicus uses), computed by WorldFires from that data. Days after the fire run until the first rain.

Open-Meteo.com (CC BY 4.0) · Copernicus Climate Change Service (ERA5)

Day High Min. humidity Peak gust Rain Danger (FWI)
2 Aug 21.7 °C 31 % 27 km/h 0.0 mm High 26
3 Aug after 22.0 °C 33 % 32 km/h 0.0 mm High 26
4 Aug after 21.8 °C 37 % 32 km/h 0.0 mm High 26
5 Aug after 22.8 °C 33 % 30 km/h 0.0 mm High 25
6 Aug after 23.0 °C 36 % 32 km/h 0.0 mm High 27
7 Aug after 23.6 °C 35 % 33 km/h 0.0 mm High 28
8 Aug after 23.0 °C 35 % 37 km/h 0.0 mm High 28
9 Aug after 22.6 °C 34 % 30 km/h 0.0 mm High 28
10 Aug after 24.6 °C 27 % 28 km/h 0.0 mm High 28
11 Aug after 25.2 °C 22 % 32 km/h 0.0 mm High 32
12 Aug after 23.6 °C 23 % 48 km/h 0.0 mm High 36

Before and after, from space

Drag the line to compare the same ground before the fire and after it.

Before · 26 Jul 2026
After · 9 Aug 2026

If the day is cloudy, change the date: each satellite passes once a day. In false colour the burnt ground looks brown or red.

The smoke

CAMS · Copernicus

On 5 August 2026 the air beside the fire reached 23 µg/m³ of PM2.5. That day averaged 19: 1.2 times the WHO daily guideline (15).

PM2.5 peak23 µg/m³
Days over the guideline1 day
PM1027 µg/m³
Optical depth0.53
3112345
Good Fair Moderate Poor Very poor Extremely poor

Particles from the Copernicus CAMS model at the centre of the perimeter; these are not measurements in each town. The pale bar is the worst hour, the solid one the daily average.

Open-Meteo.com (CC BY 4.0) · Copernicus Atmosphere Monitoring Service (CAMS)

Detections table · 27Every satellite heat detection, one by one, with time, satellite, power and coordinates.
⬇ Download CSV Times in UTC. Each detection is a 375 m pixel: a large fire yields hundreds per pass.
Date and timeSatelliteFRP (MW)LatLon

Other fires nearby

All fires in Malawi ›

Frequently asked questions

How long did the Rumphi fire last?
GWIS (Copernicus) dates it between 2 August 2026 and 2 August 2026: 1 day between the first and last heat detection of the perimeter.
How much area did it burn?
The perimeter GWIS (Copernicus) rebuilt from heat detections is 1,253 hectares (12.5 km²). It is an estimate: official national figures may differ.
Which municipalities burned?
The fire only entered Rumphi (1,261 ha, 0.3 %).
What was the weather like?
During the fire the temperature reached 21.7 °C, humidity dropped to 31 % and gusts hit 27 km/h. The fire danger index (FWI) reached 26, class High.
Where does this data come from?
From the GWIS (Copernicus) burnt perimeter, NASA FIRMS VIIRS hotspots and the administrative boundaries of Malawi (geoBoundaries). It is not an official report.

Where to verify it

A satellite detection is not an official report. Final figures and the fire’s status are published by each country’s emergency service.

Satellite cross-check

Does something look wrong on this page?

This page is built from satellite data and official records, and it sometimes gets things wrong: the wrong dates, the wrong town, two fires merged into one, or something that was not a wildfire at all. If you know this fire first-hand (you live nearby, saw it, fought it or reported on it), tell us what really happened and we will check it.

Report an error
What do you think is wrong?

We will only use your email to reply about this report. Privacy.

Where this data comes from

The perimeter comes from the Copernicus Global Wildfire Information System (GWIS), which rebuilds it from MODIS and VIIRS heat detections and publishes it under CC BY 4.0. It is not measured on imagery as in Europe, so it is an estimate. Heat detections come from the VIIRS sensors aboard Suomi-NPP and NOAA-20, distributed by NASA FIRMS at 375 m resolution. Municipal boundaries come from geoBoundaries ADM2 (Creative Commons Attribution 3.0 Intergovernmental Organisations (CC BY 3.0 IGO)). The area per municipality is computed by WorldFires by crossing the perimeter with those boundaries, so it may differ from each country’s official figure.