Skip to content
worldfires
US · United States · →

Palm Beach fire, June 2018 Palm Beach

Out · last detection 5 Jun 2018, 18:29 UTC

The fire started on 4 June 2018 in Palm Beach, United States, and satellites saw it burning for 1 day. United States agencies (MTBS / NIFC) mapped an official burnt perimeter of 4,351 hectares, spread across a single county.

It is the 13th largest in Florida since 2016 (of 148 with a page). Number 120 in United States in 2018, of 511.

The power measured by the satellite is low (19.9 MW in the strongest hotspot), more typical of grass or stubble burning, or a slow surface fire, than of a large crown fire.

Burnt area
4,351ha
official perimeter (MTBS / NIFC)
Duration
1day
4 Jun 2018 – 4 Jun 2018
Municipalities hit
1
counties
Started on
4 Jun
2018
Heat detections
77
in a single hotspot: 20 MW
Danger at start
0
Very low · FWI index
Energy released
62MW
sum of detected power

Where it burned

HOTSPOTS BY DAY 4 Jun4 Jun

How it evolved, day by day

5

Fire radiative power detected each day, in megawatts, and number of hotspots. The magenta bar marks the peak day.

The weather it burned in

34°high
32km/h · peak gust
59%lowest humidity

It had gone one day without rain (1 mm or more) when it started. Rain came after the fire: 21.2 mm on 8 Jun.

This area had burned before

3% of the perimeter overlaps earlier fires recorded since 2016: 124 ha in 2017.

What happened to each town

  1. Palm Beach where it started
    4,348 ha reached on 5 Jun
    0.8 %

Burnt area inside each county, from crossing the official perimeter with administrative boundaries. The distance is from the town centre to the nearest fire: staying a kilometre away does not mean it reached the houses.

The weather day by day

ECMWF ERA5 reanalysis at the fire location, the standard reference for past weather, and the Canadian Fire Weather Index (the same system Copernicus uses), computed by WorldFires from that data. Days after the fire run until the first rain.

Open-Meteo.com (CC BY 4.0) · Copernicus Climate Change Service (ERA5)

Day High Min. humidity Peak gust Rain Danger (FWI)
4 Jun 34.4 °C 60 % 28 km/h 3.3 mm Very low 0
5 Jun after 32.2 °C 61 % 30 km/h 3.7 mm Very low 0
6 Jun after 31.6 °C 59 % 32 km/h 5.0 mm Very low 0
7 Jun after 30.2 °C 70 % 26 km/h 23.1 mm Very low 0
8 Jun after 30.6 °C 66 % 22 km/h 21.2 mm Very low 0

Before and after, from space

Drag the line to compare the same ground before the fire and after it.

Before · 28 May 2018
After · 11 Jun 2018

If the day is cloudy, change the date: each satellite passes once a day. In false colour the burnt ground looks brown or red.

Detections table · 77Every satellite heat detection, one by one, with time, satellite, power and coordinates.
⬇ Download CSV Times in UTC. Each detection is a 375 m pixel: a large fire yields hundreds per pass.
Date and timeSatelliteFRP (MW)LatLon

Other fires nearby

All fires in United States ›

Frequently asked questions

How long did the Palm Beach fire last?
It burned between 4 June 2018 and 4 June 2018: 1 day, according to the start date recorded by United States agencies (MTBS / NIFC) and the heat detections seen by satellite.
How much area did it burn?
The official perimeter published by United States agencies (MTBS / NIFC) is 4,351 hectares (43.5 km²). Other tallies, such as daily incident reports, may give slightly different figures.
Which counties burned?
The fire only entered Palm Beach (4,348 ha, 0.8 %).
What was the weather like?
During the fire the temperature reached 34.4 °C, humidity dropped to 59 % and gusts hit 32 km/h. The fire danger index (FWI) reached 0, class Very low.
Where does this data come from?
From the official burnt perimeter of United States agencies (MTBS / NIFC, public domain), NASA FIRMS VIIRS hotspots and the administrative boundaries of United States. It is not an official report.

Where to verify it

A satellite detection is not an official report. Final figures and the fire’s status are published by each country’s emergency service.

Emergency number: 911

Satellite cross-check

Does something look wrong on this page?

This page is built from satellite data and official records, and it sometimes gets things wrong: the wrong dates, the wrong town, two fires merged into one, or something that was not a wildfire at all. If you know this fire first-hand (you live nearby, saw it, fought it or reported on it), tell us what really happened and we will check it.

Report an error
What do you think is wrong?

We will only use your email to reply about this report. Privacy. This is not an emergency service: if there is a fire now, call 911.

Where this data comes from

The perimeter is official and in the public domain. For past years it comes from MTBS (Monitoring Trends in Burn Severity), run by the U.S. Geological Survey and the USDA Forest Service, which map it on Landsat and Sentinel-2 imagery. For the current and last year it comes from WFIGS at the National Interagency Fire Center (NIFC): incident perimeters mapped by fire crews, aircraft and imagery. Heat detections come from the VIIRS sensors aboard Suomi-NPP and NOAA-20, distributed by NASA FIRMS at 375 m resolution. County boundaries come from geoBoundaries ADM2 (Public Domain). The area per county is computed by WorldFires by crossing the perimeter with those boundaries, so it may differ slightly from official figures.