Mbire fire, 17 September 2018 Mbire
The fire started on 17 September 2018 in Mbire, Zimbabwe, and satellites saw it burning for 13 days. Copernicus’s global GWIS system rebuilt a burnt perimeter of 2,213 hectares from heat detections, spread across a single municipality.
It is the 36th largest in Mashonaland Central since 2016 (of 334 with a page). Number 60 in Zimbabwe in 2018, of 265.
The power measured by the satellite is low (12.9 MW in the strongest hotspot), more typical of grass or stubble burning, or a slow surface fire, than of a large crown fire.
Compare with…
- Burnt area
- 2,213ha
- GWIS perimeter (Copernicus)
- Duration
- 13days
- 17 Sept 2018 – 29 Sept 2018
- Municipalities hit
- 1
- districts
- Started on
- 17 Sept
- 2018
- Heat detections
- 86
- in a single hotspot: 13 MW
- Average daily power
- 38MW
- detected power per day, on average
Where it burned
How it evolved, day by day
Fire radiative power detected each day, in megawatts, and number of hotspots. The magenta bar marks the peak day.
This area had burned before
2% of the perimeter overlaps earlier fires recorded since 2016: 52 ha in 2017.
How big is it?
London boundary: geoBoundaries · Office for National Statistics (Open Government Licence v3.0).
Paris boundary: geoBoundaries · Institut national de l'information géographique et forestière (IGN-F) (Etalab Open License 2.0).
Madrid boundary: geoBoundaries · Open Data ESRI, IGN Central Registry of Cartography Area (CC BY 4.0).
Berlin boundary: geoBoundaries · Federal Agency for Cartography and Geodesy (dl-de/by-2-0).
This compares size, not location: both shapes are at the same scale, north up, centred on each other.
What happened to each town
-
Mbire where it started2,225 ha reached on 21 Sept0.5 %
Burnt area inside each municipality, from crossing the GWIS perimeter with administrative boundaries. The distance runs from the point marking the centre of each area to the nearest fire: staying a kilometre away does not mean it reached the houses.
People and buildings inside the perimeter
GHSL 2020Inside the perimeter there was no noticeable built-up land and almost nobody lived there (GHSL 2020, satellite-based estimate).
This is an estimate on 100 m cells, made from satellite imagery and census data: it does not mean that homes burned or that anyone was harmed. The perimeter also contains land that never burned.
Source: Global Human Settlement Layer (GHS-BUILT-S and GHS-POP R2023A), European Commission Joint Research Centre (JRC), © European Union, CC BY 4.0. Sum inside the perimeter computed by WorldFires. human-settlement.emergency.copernicus.eu
Before and after, from space
Drag the line to compare the same ground before the fire and after it.
If the day is cloudy, change the date: each satellite passes once a day. In false colour the burnt ground looks brown or red.
Detections table · 86Every satellite heat detection, one by one, with time, satellite, power and coordinates.
| Date and time | Satellite | FRP (MW) | Lat | Lon |
|---|
Other fires nearby
- 12,300 haHurungwe11 September 2020 · 18 days · 15 km away
- 23,001 haHurungwe28 September 2022 · 20 days · 17 km away
- 31,897 haHurungwe20 September 2026 · 10 days · 20 km away
- 16,625 haHurungwe19 September 2019 · 11 days · 23 km away
- 18,057 haHurungwe4 September 2021 · 8 days · 25 km away
- 33,869 haHurungwe26 August 2018 · 51 days · 29 km away
Frequently asked questions
- How long did the Mbire fire last?
- According to the heat detections seen by satellite inside the perimeter, it burned from 17 September 2018 to 29 September 2018 (13 days). The perimeter dates it from 23 September 2018 to 27 September 2018.
- How much area did it burn?
- The perimeter GWIS (Copernicus) rebuilt from heat detections is 2,213 hectares (22.1 km²). It is an estimate: official national figures may differ.
- Which municipalities burned?
- The fire only entered Mbire (2,225 ha, 0.5 %).
- Where does this data come from?
- From the GWIS (Copernicus) burnt perimeter, NASA FIRMS VIIRS hotspots and the administrative boundaries of Zimbabwe (geoBoundaries). It is not an official report.
Where to verify it
A satellite detection is not an official report. Final figures and the fire’s status are published by each country’s emergency service.
Satellite cross-check
History of this page Changes in area, dates, name, official record or merged pages, compared every night since 24 October 2026.
No changes since 24 October 2026.
Does something look wrong on this page?
This page is built from satellite data and official records, and it sometimes gets things wrong: the wrong dates, the wrong town, two fires merged into one, or something that was not a wildfire at all. If you know this fire first-hand (you live nearby, saw it, fought it or reported on it), tell us what really happened and we will check it.
Report an error
How we know this
- Perimeter: GWIS (Copernicus), rebuilt from heat detections rather than mapped on imagery.
- Dates adjusted with the VIIRS detections inside the perimeter, which said 23 September 2018 to 27 September 2018. 86 Suomi-NPP VIIRS detections on those dates.
- We have not matched this page with any official record.
- Built-up area and population come from the JRC Global Human Settlement Layer (epoch 2020, 100 m cells), summed inside the perimeter: an estimate of what was there, not a damage count.
Where this data comes from
The perimeter comes from the Copernicus Global Wildfire Information System (GWIS), which rebuilds it from MODIS and VIIRS heat detections and publishes it under CC BY 4.0. It is not measured on imagery as in Europe, so it is an estimate. Heat detections come from the VIIRS sensors aboard Suomi-NPP and NOAA-20, distributed by NASA FIRMS at 375 m resolution. Municipal boundaries come from geoBoundaries ADM2 (Creative Commons Attribution 3.0 Intergovernmental Organisations (CC BY 3.0 IGO)). The area per municipality is computed by WorldFires by crossing the perimeter with those boundaries, so it may differ from each country’s official figure.