Burned area
satellite only1,207ha
Perimeter published by GWIS (Copernicus).
- Source
- GWIS (Copernicus)
- Date
- 10 Mar 2019 – 24 Mar 2019
+− cross-check
No official record is matched to this page to compare it with.
CR · Costa Rica · –
Liberia fire, 10 March 2019 Liberia
Out · last detection 24 Mar 2019, 07:43 UTC
The fire started on 10 March 2019 in Liberia, Costa Rica, and satellites saw it burning for 15 days. Copernicus’s global GWIS system rebuilt a burnt perimeter of 1,207 hectares from heat detections, spread across a single municipality.
It is the 66th largest in Provincia Guanacaste since 2016 (of 88 with a page). Number 12 in Costa Rica in 2019, of 16.
The power measured by the satellite is low (8.7 MW in the strongest hotspot), more typical of grass or stubble burning, or a slow surface fire, than of a large crown fire.
Use this data
Compare with…
Use this data
Fire page data · version 2026-10-25matches the official recordwith caveatssatellite onlymodel
When copying, the sentence is
Tick the figures you want: they make up the lede and the CSV.
Duration by satellite
satellite only15days
10 Mar 2019 to 24 Mar 2019: first and last day with fire on the page.
- Source
- GWIS (Copernicus) · NASA FIRMS · VIIRS
- Date
- last detection: 24 Mar 2019, 07:43 UTC
+− cross-check
Satellites pass a few times a day and cloud or smoke can hide the fire: a lack of detections is not an official extinction. Each country’s emergency service declares a fire contained or out.
Start
satellite only10 Mar 2019
First day with fire seen by the satellites or the perimeter.
- Source
- GWIS (Copernicus) · NASA FIRMS · VIIRS
- Date
- 10 Mar 2019
+− cross-check
No official record is matched to this page, so the alert time and the cause are not known here.
Hotspots
satellite only35
VIIRS detections at 375 m. Most intense hotspot: 9 MW.
- Source
- NASA FIRMS · VIIRS (Suomi NPP)
- Date
- 10 Mar 2019 – 24 Mar 2019
+− cross-check
There is no official record to compare with. Each hotspot is a pixel detected in one satellite pass, not a separate fire.
The worst day
satellite only41MW
Total radiative power on 20 March 2019; hotspots that day: 9.
- Source
- NASA FIRMS · VIIRS (FRP)
- Date
- 20 Mar 2019
+− cross-check
Fire radiative power (FRP) measures the energy the fire gives off when the satellite passes. Added up by day, it compares intensity, not area.
Danger at the start
model31.8FWI · high
Fire Weather Index (Canadian system) computed by WorldFires for the day the fire started. Consecutive days without rain before: 60.
- Source
- WorldFires calculation (Canadian FWI system)
- Date
- 10 Mar 2019, local noon
- Model
- ERA5 0,25° (ECMWF · Copernicus C3S) · Open-Meteo.com
+− cross-check
This is an index computed from weather model data, not a measurement of the fire nor an official warning. Danger warnings are issued by each country’s authority. Emergency number and official warnings
Weather during the fire
model34.6°C · 44% RH
High of 34.6 °C and minimum humidity of 44% on 19 March 2019; gusts of 72 km/h on 17 March 2019.
- Source
- weather model at the fire’s grid cell
- Date
- 10 Mar 2019 – 24 Mar 2019
- Model
- ERA5 0,25° (ECMWF · Copernicus C3S) · Open-Meteo.com
+− cross-check
These are model values for a cell of about 25 km, not from a weather station: they may differ from what was measured on the ground.
Living inside
model≈ 200people
Estimated residents inside the perimeter and 2.2 ha of built-up area (100 m grid, epoch 2020).
- Source
- GHSL R2023A · JRC
- Date
- calculated on 24 October 2026
+− cross-check
This is an estimate on 100 m cells, made from satellite imagery and census data: it does not mean that homes burned or that anyone was harmed. The perimeter also contains land that never burned.
This page’s change log has been kept since 24 October 2026: every night what it publishes is compared and the difference is logged. Anything earlier is reconstructed from each source’s date and marked as reconstructed.
Show
-
· reconstructed weatherWeather and FWI computed from the ERA5 reanalysis
-
logStart date: 17 March 2019 → 10 March 2019.
-
· reconstructed GHSLPopulation and built-up area computed
What was saved on 25 October 2026
Every night a snapshot of what the page shows is saved. If anything changes, it appears in the list as a log entry.
- Area
- 1,207 ha
- Dates
- 10 Mar 2019 – 24 Mar 2019
- Name
- Liberia
- Official record
- —
Versioned permanent link
https://worldfires.org/en/fire/liberia-2019-03-2?v=2026-10-25A version keeps the area, dates, name and official record; the area as it was logged (changes under 2% are not logged). The map, hotspots and weather always show today’s data.
Citation
A lede of about 60 words figures only, no adjectives
CSV for this fire liberia-2019-03-2.csv · daily, no individual hotspots
| fecha | focos_viirs | frp_mw | tmax_c | tmin_c | hr_min_pct | viento_max_kmh | racha_max_kmh | precip_mm | fwi | clase_fwi | dentro_del_incendio |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 2019-03-10 | 0 | 0 | 32.2 | 24.1 | 50 | 24 | 59.8 | 0 | 31.8 | alto | 1 |
| 2019-03-11 | 0 | 0 | 32.4 | 24.2 | 53 | 27.4 | 68.4 | 0 | 34.3 | alto | 1 |
| 2019-03-12 | 0 | 0 | 32.6 | 25.2 | 49 | 28.7 | 70.9 | 0 | 35.7 | alto | 1 |
| 2019-03-13 | 0 | 0 | 32.5 | 24.4 | 44 | 22.9 | 59.8 | 0 | 31.3 | alto | 1 |
| 2019-03-14 | 0 | 0 | 34.2 | 23 | 42 | 17.2 | 45.7 | 0 | 28.6 | alto | 1 |
| 2019-03-15 | 1 | 2 | 33.3 | 22.8 | 47 | 19.3 | 47.9 | 0 | 30.4 | alto | 1 |
| 2019-03-16 | 0 | 0 | 31.5 | 25 | 52 | 26.6 | 66.2 | 0 | 34.6 | alto | 1 |
| 2019-03-17 | 1 | 4 | 31.4 | 24.2 | 54 | 28.2 | 72 | 0 | 34.8 | alto | 1 |
| 2019-03-18 | 12 | 36 | 31.9 | 23.6 | 47 | 25.8 | 61.2 | 0 | 33.1 | alto | 1 |
| 2019-03-19 | 2 | 17 | 34.6 | 23.5 | 44 | 17.8 | 46.1 | 0 | 28.8 | alto | 1 |
| 2019-03-20 | 9 | 41 | 33.3 | 22.5 | 50 | 19.5 | 50 | 0 | 30.3 | alto | 1 |
| 2019-03-21 | 5 | 23 | 32.6 | 24.8 | 49 | 22.7 | 56.5 | 0 | 33 | alto | 1 |
| 2019-03-22 | 0 | 0 | 31.7 | 24.9 | 51 | 26.3 | 65.9 | 0 | 35.7 | alto | 1 |
| 2019-03-23 | 4 | 4 | 32.7 | 23.1 | 47 | 25.6 | 63.7 | 0 | 35.3 | alto | 1 |
| 2019-03-24 | 1 | 2 | 32.6 | 22.8 | 48 | 23.5 | 60.5 | 0 | 33.8 | alto | 1 |
| 2019-03-25 | 0 | 0 | 32.2 | 22.7 | 54 | 22 | 56.2 | 0 | 31.1 | alto | 0 |
| 2019-03-26 | 0 | 0 | 32.9 | 25.1 | 48 | 26.3 | 65.2 | 0 | 34.8 | alto | 0 |
| 2019-03-27 | 0 | 0 | 31.9 | 25.2 | 48 | 30.9 | 75.2 | 0 | 39.2 | muy_alto | 0 |
| 2019-03-28 | 0 | 0 | 31.9 | 25 | 50 | 28 | 68.8 | 0 | 36.8 | alto | 0 |
| 2019-03-29 | 0 | 0 | 32.8 | 22.9 | 48 | 21.9 | 56.5 | 0 | 31.9 | alto | 0 |
| 2019-03-30 | 0 | 0 | 34 | 22.2 | 42 | 19.7 | 48.6 | 0 | 31.9 | alto | 0 |
| 2019-03-31 | 0 | 0 | 35.2 | 21.5 | 39 | 16.1 | 43.9 | 0 | 31.3 | alto | 0 |
| 2019-04-01 | 0 | 0 | 34.5 | 21.9 | 38 | 14.8 | 41.4 | 0 | 30.7 | alto | 0 |
| 2019-04-02 | 0 | 0 | 34.3 | 24.5 | 47 | 19.7 | 51.5 | 0 | 34.7 | alto | 0 |
| 2019-04-03 | 0 | 0 | 33.8 | 25 | 45 | 25.1 | 62.6 | 0 | 39.8 | muy_alto | 0 |
It is generated in your browser from this page’s data: one file per fire, aggregated by day and without individual hotspots.
Live widget for your story
It updates itself while the fire is still active and links to this page. Free, with the attribution shown at the bottom.
Sources for this page: GWIS (Copernicus), NASA FIRMS (VIIRS), ERA5 (ECMWF/Copernicus C3S) · Open-Meteo.com (CC BY 4.0), GHSL (JRC). Open-Meteo.com · How we build fire pages: methodology
- Burnt area
- 1,207ha
- GWIS perimeter (Copernicus)
- Duration
- 15days
- 10 Mar 2019 – 24 Mar 2019
- Municipalities hit
- 1
- cantons
- Started on
- 10 Mar
- 2019
- Heat detections
- 35
- in a single hotspot: 9 MW
- Danger at start
- 32
- High · FWI index
- Average daily power
- 16MW
- detected power per day, on average
Where it burned
HOTSPOTS BY DAY
10 Mar24 Mar
24 Mar 2019
How it evolved, day by day
15 Mar
18 Mar
20 Mar
23 Mar
Fire radiative power detected each day, in megawatts, and number of hotspots. The magenta bar marks the peak day.
The weather it burned in
35°high
72km/h · peak gust
42%lowest humidity
It had gone more than two months without rain (1 mm or more) when it started.
This area had burned before
No earlier perimeters overlap this fire since 2016, when the satellite record begins.
How big is it?
London boundary: geoBoundaries · Office for National Statistics (Open Government Licence v3.0).
Paris boundary: geoBoundaries · Institut national de l'information géographique et forestière (IGN-F) (Etalab Open License 2.0).
Madrid boundary: geoBoundaries · Open Data ESRI, IGN Central Registry of Cartography Area (CC BY 4.0).
Berlin boundary: geoBoundaries · Federal Agency for Cartography and Geodesy (dl-de/by-2-0).
This compares size, not location: both shapes are at the same scale, north up, centred on each other.
What happened to each town
-
Liberia where it started1,215 ha reached on 15 Mar0.8 %
Burnt area inside each municipality, from crossing the GWIS perimeter with administrative boundaries. The distance runs from the point marking the centre of each area to the nearest fire: staying a kilometre away does not mean it reached the houses.
People and buildings inside the perimeter
GHSL 2020Built-up area2.2 ha
Residents≈ 200
Inside the perimeter there were about 2.2 hectares of built-up land and about 200 residents (GHSL 2020, satellite-based estimate).
This is an estimate on 100 m cells, made from satellite imagery and census data: it does not mean that homes burned or that anyone was harmed. The perimeter also contains land that never burned.
Source: Global Human Settlement Layer (GHS-BUILT-S and GHS-POP R2023A), European Commission Joint Research Centre (JRC), © European Union, CC BY 4.0. Sum inside the perimeter computed by WorldFires. human-settlement.emergency.copernicus.eu
The weather day by day
ECMWF ERA5 reanalysis at the fire location, the standard reference for past weather, and the Canadian Fire Weather Index (the same system Copernicus uses), computed by WorldFires from that data. Days after the fire run until the first rain.
Open-Meteo.com (CC BY 4.0) · Copernicus Climate Change Service (ERA5)
Started with Strong wind: 50 % of the area in Costa Rica 60 days without rain: 45 % of the area in Costa Rica
| Day | High | Min. humidity | Peak gust | Rain | Danger (FWI) |
|---|---|---|---|---|---|
| 10 Mar | 32.2 °C | 50 % | 60 km/h | 0.0 mm | High 32 |
| 11 Mar | 32.4 °C | 53 % | 68 km/h | 0.0 mm | High 34 |
| 12 Mar | 32.6 °C | 49 % | 71 km/h | 0.0 mm | High 36 |
| 13 Mar | 32.5 °C | 44 % | 60 km/h | 0.0 mm | High 31 |
| 14 Mar | 34.2 °C | 42 % | 46 km/h | 0.0 mm | High 29 |
| 15 Mar | 33.3 °C | 47 % | 48 km/h | 0.0 mm | High 30 |
| 16 Mar | 31.5 °C | 52 % | 66 km/h | 0.0 mm | High 35 |
| 17 Mar | 31.4 °C | 54 % | 72 km/h | 0.0 mm | High 35 |
| 18 Mar | 31.9 °C | 47 % | 61 km/h | 0.0 mm | High 33 |
| 19 Mar | 34.6 °C | 44 % | 46 km/h | 0.0 mm | High 29 |
| 20 Mar | 33.3 °C | 50 % | 50 km/h | 0.0 mm | High 30 |
| 21 Mar | 32.6 °C | 49 % | 56 km/h | 0.0 mm | High 33 |
| 22 Mar | 31.7 °C | 51 % | 66 km/h | 0.0 mm | High 36 |
| 23 Mar | 32.7 °C | 47 % | 64 km/h | 0.0 mm | High 35 |
| 24 Mar | 32.6 °C | 48 % | 60 km/h | 0.0 mm | High 34 |
| 25 Mar after | 32.2 °C | 54 % | 56 km/h | 0.0 mm | High 31 |
| 26 Mar after | 32.9 °C | 48 % | 65 km/h | 0.0 mm | High 35 |
| 27 Mar after | 31.9 °C | 48 % | 75 km/h | 0.0 mm | Very high 39 |
| 28 Mar after | 31.9 °C | 50 % | 69 km/h | 0.0 mm | High 37 |
| 29 Mar after | 32.8 °C | 48 % | 56 km/h | 0.0 mm | High 32 |
| 30 Mar after | 34.0 °C | 42 % | 49 km/h | 0.0 mm | High 32 |
| 31 Mar after | 35.2 °C | 39 % | 44 km/h | 0.0 mm | High 31 |
| 1 Apr after | 34.5 °C | 38 % | 41 km/h | 0.0 mm | High 31 |
| 2 Apr after | 34.3 °C | 47 % | 52 km/h | 0.0 mm | High 35 |
| 3 Apr after | 33.8 °C | 45 % | 63 km/h | 0.0 mm | Very high 40 |
Its twins: fires that started in the same weather
It started with an FWI of 31.8, a minimum humidity of 50% and more than two months without rain. Fires in the area that started in weather like this since 2016: 20.
FWI at the start
31.8
Minimum humidity
50 %
Days without rain
60+
this fire
chosen twins
rest of the area
Almost identicalSimilar
Outlines of the closest twins
This fire · Liberia fire, 10 March 2019
1,207 ha
15 days
FWI 31.8
Min. humidity 50 %
Carrillo fire, March 2022
1,103 ha
5 days
FWI 33.0
Min. humidity 48 %
36 km away, in 2022
First rain (1 mm or more) after it ended: none in the following ten days.
Bagaces fire, February 2022
1,028 ha
4 days
FWI 29.1
Min. humidity 51 %
44 km away, in 2022
First rain (1 mm or more) after it ended: none in the following ten days.
Liberia fire, February 2017
1,161 ha
8 days
FWI 30.4
Min. humidity 50 %
13 km away, in 2017
First rain (1 mm or more) after it ended: none in the following ten days.
Carrillo fire, February 2022
11,946 ha
29 days
FWI 30.5
Min. humidity 47 %
31 km away, in 2022
First rain (1 mm or more) after it ended: none in the following ten days.
Liberia fire, March 2017
1,267 ha
7 days
FWI 29.8
Min. humidity 47 %
14 km away, in 2017
First rain (1 mm or more) after it ended: 7.2 mm on 2 Apr.
What happened to them
- 8 days
- median duration
- 1,568 ha
- median area
- 100 %
- went past 1,000 ha
- 3.3 mm
- rain at the end (median; 5 of 20 had it)
It burned an area similar to its twins (1,207 ha against a median of 1,568 ha) and lasted 15 days, against 8 days.
In 15 of 20, not even 1 mm fell in the ten days after the end: they went out without rain. In the rest, the first rainy day brought a median of 3.3 mm.
This is a bank of analogues: it shows what usually happens, not what will happen. With fewer than 15 twins we give no figures. How we calculate it
How it ended
—first rain
—no rain in ten days
72km/h · max. gust
It was considered over on 24 Mar, and not even 1 mm fell in the following ten days: it went out without rain. Twins with rain when they ended: 5 of 20, with a median of 3.3 mm.
Weather on this page: Open-Meteo.com (CC BY 4.0) · Copernicus Climate Change Service (ERA5)
How a twin is chosen
- Same area: fires that have already ended, less than 250 km from this one, since 2016.
- Same start: we compare the FWI on the first day, the minimum humidity that day and the run of days without rain before it. The slider sets how much they may differ.
- Only pages with final weather data (ERA5 reanalysis) calculated in the same way as this fire’s; agricultural and grass burns and pages with data under review are left out.
- Fires burning at the same time as this one (a week before or after) are left out: they share the same spell of weather and do not count as a precedent.
- They are sorted by similarity, and the outlines of the first five are drawn.
Before and after, from space
Drag the line to compare the same ground before the fire and after it.
↔
Before · 3 Mar 2019
After · 31 Mar 2019
Sentinel-2 did not pass over on that day. Try another date, or use false colour, which is daily.
If the day is cloudy, change the date: each satellite passes once a day. In false colour the burnt ground looks brown or red.
Detections table · 35Every satellite heat detection, one by one, with time, satellite, power and coordinates.
⬇ Download CSV
Times in UTC. Each detection is a 375 m pixel: a large fire yields hundreds per pass.
| Date and time | Satellite | FRP (MW) | Lat | Lon |
|---|
Other fires nearby
- 3,714 haLiberiaFebruary 2022 · 10 days · 10 km away
- 4,113 haBagaces4 May 2026 · 13 days · 20 km away
- 5,841 haCarrilloMarch 2020 · 27 days · 30 km away
- 11,946 haCarrillo6 February 2022 · 29 days · 31 km away
- 4,757 haLa Cruz7 April 2026 · 25 days · 33 km away
- 15,034 haCarrilloJanuary 2026 · 56 days · 34 km away
Frequently asked questions
- How long did the Liberia fire last?
- According to the heat detections seen by satellite inside the perimeter, it burned from 10 March 2019 to 24 March 2019 (15 days). The perimeter dates it from 17 March 2019 to 24 March 2019.
- How much area did it burn?
- The perimeter GWIS (Copernicus) rebuilt from heat detections is 1,207 hectares (12.1 km²). It is an estimate: official national figures may differ.
- Which municipalities burned?
- The fire only entered Liberia (1,215 ha, 0.8 %).
- What was the weather like?
- During the fire the temperature reached 34.6 °C, humidity dropped to 42 % and gusts hit 72 km/h. The fire danger index (FWI) reached 36, class High.
- Where does this data come from?
- From the GWIS (Copernicus) burnt perimeter, NASA FIRMS VIIRS hotspots and the administrative boundaries of Costa Rica (geoBoundaries). It is not an official report.
- How did the fires that started in similar weather in this area end?
- Fires less than 250 km away that started since 2016 with a similar FWI, humidity and dry spell: 20. Their median duration was 8 days and their median area 1,568 ha; 100 % went past 1,000 ha. In 15 of 20, not even 1 mm fell in the ten days after the end: they went out without rain. In the rest, the first rainy day brought a median of 3.3 mm.
Where to verify it
A satellite detection is not an official report. Final figures and the fire’s status are published by each country’s emergency service.
Emergency number: 911 · Emergency number and official warnings
Satellite cross-check
History of this page · 1 Changes in area, dates, name, official record or merged pages, compared every night since 24 October 2026.
- Start date: 17 March 2019 → 10 March 2019.
RSS Changes to this page With cross-checks and a citable version
Does something look wrong on this page?
This page is built from satellite data and official records, and it sometimes gets things wrong: the wrong dates, the wrong town, two fires merged into one, or something that was not a wildfire at all. If you know this fire first-hand (you live nearby, saw it, fought it or reported on it), tell us what really happened and we will check it.
Report an error
How we know this
- Perimeter: GWIS (Copernicus), rebuilt from heat detections rather than mapped on imagery.
- Dates adjusted with the VIIRS detections inside the perimeter, which said 17 March 2019 to 24 March 2019. 35 Suomi-NPP VIIRS detections on those dates.
- We have not matched this page with any official record.
- Weather: Copernicus ERA5 reanalysis at the fire location, in cells of about 25 km.
- Built-up area and population come from the JRC Global Human Settlement Layer (epoch 2020, 100 m cells), summed inside the perimeter: an estimate of what was there, not a damage count.
Where this data comes from
The perimeter comes from the Copernicus Global Wildfire Information System (GWIS), which rebuilds it from MODIS and VIIRS heat detections and publishes it under CC BY 4.0. It is not measured on imagery as in Europe, so it is an estimate. Heat detections come from the VIIRS sensors aboard Suomi-NPP and NOAA-20, distributed by NASA FIRMS at 375 m resolution. Municipal boundaries come from geoBoundaries ADM2 (CC0 1.0 Universal (CC0 1.0) Public Domain Dedication). The area per municipality is computed by WorldFires by crossing the perimeter with those boundaries, so it may differ from each country’s official figure.