Skip to content
worldfires
TH · Thailand · →

Khlong Lan fire, March 2023 Khlong Lan

Out · last detection 25 Mar 2023, 19:22 UTC

The fire started on 21 March 2023 in Khlong Lan, Thailand, and satellites saw it burning for 5 days. Copernicus’s global GWIS system rebuilt a burnt perimeter of 1,316 hectares from heat detections, spread across a single municipality.

It is the 45th largest in Kamphaeng Phet Province since 2016 (of 66 with a page). Number 321 in Thailand in 2023, of 500.

Burnt area
1,316ha
GWIS perimeter (Copernicus)
Duration
5days
21 Mar 2023 – 25 Mar 2023
Municipalities hit
1
districts
Started on
21 Mar
2023
Heat detections
34
in a single hotspot: 32 MW
Danger at start
14
Moderate · FWI index
Energy released
184MW
sum of detected power

Where it burned

25 Mar 2023
HOTSPOTS BY DAY 21 Mar25 Mar

How it evolved, day by day

2122232425

Fire radiative power detected each day, in megawatts, and number of hotspots. The magenta bar marks the peak day.

The weather it burned in

34°high
28km/h · peak gust
31%lowest humidity

It had gone 3 days without rain (1 mm or more) when it started.

This area had burned before

87% of the perimeter overlaps earlier fires recorded since 2016: 209 ha in 2016, 663 ha in 2017, 595 ha in 2019, 137 ha in 2020, 816 ha in 2021, 12 ha in 2022. Part of it burned more than once, so the yearly figures add up to more than the 1,139 ha that had burned before.

What happened to each town

  1. Khlong Lan where it started
    1,324 ha reached on 21 Mar
    0.9 %

Burnt area inside each municipality, from crossing the GWIS perimeter with administrative boundaries. The distance is from the town centre to the nearest fire: staying a kilometre away does not mean it reached the houses.

The weather day by day

ECMWF ERA5 reanalysis at the fire location, the standard reference for past weather, and the Canadian Fire Weather Index (the same system Copernicus uses), computed by WorldFires from that data. Days after the fire run until the first rain.

Open-Meteo.com (CC BY 4.0) · Copernicus Climate Change Service (ERA5)

Day High Min. humidity Peak gust Rain Danger (FWI)
17 Mar 30.5 °C 51 % 24 km/h 0.2 mm Moderate 14
18 Mar 31.2 °C 50 % 28 km/h 1.8 mm Low 7
19 Mar 30.2 °C 53 % 25 km/h 0.8 mm Low 10
20 Mar 31.3 °C 54 % 22 km/h 2.0 mm Very low 5
21 Mar 32.7 °C 46 % 23 km/h 1.4 mm Low 8
22 Mar 34.1 °C 37 % 22 km/h 0.0 mm Moderate 17
23 Mar 33.6 °C 37 % 23 km/h 0.1 mm Moderate 20
24 Mar 33.9 °C 36 % 24 km/h 0.0 mm Moderate 21
25 Mar 34.4 °C 31 % 21 km/h 0.0 mm High 24
26 Mar after 34.2 °C 32 % 22 km/h 0.0 mm High 24
27 Mar after 33.5 °C 34 % 30 km/h 0.0 mm High 24
28 Mar after 32.6 °C 42 % 30 km/h 0.0 mm High 24
29 Mar after 33.2 °C 38 % 24 km/h 0.0 mm High 22
30 Mar after 34.3 °C 33 % 19 km/h 0.0 mm High 23
31 Mar after 32.7 °C 40 % 24 km/h 0.0 mm High 24
1 Apr after 32.2 °C 46 % 30 km/h 0.0 mm High 22
2 Apr after 32.6 °C 43 % 22 km/h 0.0 mm High 22
3 Apr after 34.5 °C 30 % 23 km/h 0.0 mm High 27
4 Apr after 33.3 °C 37 % 25 km/h 0.0 mm High 28

Before and after, from space

Drag the line to compare the same ground before the fire and after it.

Before · 14 Mar 2023
After · 1 Apr 2023

If the day is cloudy, change the date: each satellite passes once a day. In false colour the burnt ground looks brown or red.

The smoke

CAMS · Copernicus

On 27 March 2023 the air beside the fire reached 47 µg/m³ of PM2.5. That day averaged 36: 2.4 times the WHO daily guideline (15).

PM2.5 peak47 µg/m³
Days over the guideline7 days
PM1067 µg/m³
Optical depth0.92
19202122232425262728
Good Fair Moderate Poor Very poor Extremely poor

Particles from the Copernicus CAMS model at the centre of the perimeter; these are not measurements in each town. The pale bar is the worst hour, the solid one the daily average.

Open-Meteo.com (CC BY 4.0) · Copernicus Atmosphere Monitoring Service (CAMS)

Detections table · 34Every satellite heat detection, one by one, with time, satellite, power and coordinates.
⬇ Download CSV Times in UTC. Each detection is a 375 m pixel: a large fire yields hundreds per pass.
Date and timeSatelliteFRP (MW)LatLon

Other fires nearby

All fires in Thailand ›

Frequently asked questions

How long did the Khlong Lan fire last?
GWIS (Copernicus) dates it between 21 March 2023 and 25 March 2023: 5 days between the first and last heat detection of the perimeter.
How much area did it burn?
The perimeter GWIS (Copernicus) rebuilt from heat detections is 1,316 hectares (13.2 km²). It is an estimate: official national figures may differ.
Which municipalities burned?
The fire only entered Khlong Lan (1,324 ha, 0.9 %).
What was the weather like?
During the fire the temperature reached 34.4 °C, humidity dropped to 31 % and gusts hit 28 km/h. The fire danger index (FWI) reached 24, class High.
Where does this data come from?
From the GWIS (Copernicus) burnt perimeter, NASA FIRMS VIIRS hotspots and the administrative boundaries of Thailand (geoBoundaries). It is not an official report.

Where to verify it

A satellite detection is not an official report. Final figures and the fire’s status are published by each country’s emergency service.

Emergency number: 199 · 191

Satellite cross-check

Does something look wrong on this page?

This page is built from satellite data and official records, and it sometimes gets things wrong: the wrong dates, the wrong town, two fires merged into one, or something that was not a wildfire at all. If you know this fire first-hand (you live nearby, saw it, fought it or reported on it), tell us what really happened and we will check it.

Report an error
What do you think is wrong?

We will only use your email to reply about this report. Privacy. This is not an emergency service: if there is a fire now, call 199 · 191.

Where this data comes from

The perimeter comes from the Copernicus Global Wildfire Information System (GWIS), which rebuilds it from MODIS and VIIRS heat detections and publishes it under CC BY 4.0. It is not measured on imagery as in Europe, so it is an estimate. Heat detections come from the VIIRS sensors aboard Suomi-NPP and NOAA-20, distributed by NASA FIRMS at 375 m resolution. Municipal boundaries come from geoBoundaries ADM2 (Creative Commons Attribution 3.0 Intergovernmental Organisations (CC BY 3.0 IGO)). The area per municipality is computed by WorldFires by crossing the perimeter with those boundaries, so it may differ from each country’s official figure.