Skip to content
worldfires
UK · United Kingdom · →

Highland fire, 15 April 2018 Highland

Out · last detection 15 Apr 2018, 14:30 UTC

The fire started on 15 April 2018 in Highland, United Kingdom, and satellites saw it burning for 1 day. Copernicus mapped a burnt perimeter of 2,755 hectares from satellite imagery, spread across a single municipality.

It is the 6th largest in Scotland since 2016 (of 49 with a page). The largest in United Kingdom in 2018, of 19.

Compare with…
Burnt area
2,755ha
Copernicus perimeter
Duration
1day
15 Apr 2018 – 15 Apr 2018
Municipalities hit
1
districts
Started on
15 Apr
2018
Heat detections
42
in a single hotspot: 75 MW
Danger at start
4
Very low · FWI index
Average daily power
363MW
detected power per day, on average

Where it burned

HOTSPOTS BY DAY 15 Apr15 Apr

How it evolved, day by day

15 Apr 2018 · 363 MW · 42

Fire radiative power detected each day, in megawatts, and number of hotspots. The magenta bar marks the peak day.

The weather it burned in

14°high
44km/h · peak gust
55%lowest humidity

It had gone 3 days without rain (1 mm or more) when it started. Rain came after the fire: 3.2 mm on 17 Apr.

This area had burned before

No earlier perimeters overlap this fire since 2016, when the satellite record begins.

How big is it?

10 km
It burned the equivalent of 1.7% of the area of London (28 km² against 1,583 km²).

London boundary: geoBoundaries · Office for National Statistics (Open Government Licence v3.0).

This compares size, not location: both shapes are at the same scale, north up, centred on each other.

What happened to each town

  1. Highland where it started
    2,810 ha reached on 15 Apr
    0.1 %

Burnt area inside each municipality, from crossing the official perimeter with administrative boundaries. The distance runs from the point marking the centre of each area to the nearest fire: staying a kilometre away does not mean it reached the houses.

What burned

  • Other natural land99 %

Protected area affected (EFFIS layer): 60 %

Land cover inside the perimeter according to Corine Land Cover, as reported by Copernicus.

The weather day by day

ECMWF ERA5 reanalysis at the fire location, the standard reference for past weather, and the Canadian Fire Weather Index (the same system Copernicus uses), computed by WorldFires from that data. Days after the fire run until the first rain.

Open-Meteo.com (CC BY 4.0) · Copernicus Climate Change Service (ERA5)

Day High Min. humidity Peak gust Rain Danger (FWI)
15 Apr 14.4 °C 55 % 44 km/h 0.0 mm Very low 4
16 Apr after 14.0 °C 57 % 53 km/h 0.1 mm Very low 5
17 Apr after 15.6 °C 50 % 71 km/h 3.2 mm Very low 1

Before and after, from space

Drag the line to compare the same ground before the fire and after it.

Before · 8 Apr 2018
After · 22 Apr 2018

If the day is cloudy, change the date: each satellite passes once a day. In false colour the burnt ground looks brown or red.

The smoke

CAMS · Copernicus

On 15 April 2018 the air beside the fire reached 14 µg/m³ of PM2.5, but no daily average passed the WHO guideline (15).

PM2.5 peak14 µg/m³
Days over the guideline0 days
PM1020 µg/m³
131415161718
Good Fair Moderate Poor Very poor Extremely poor

Particles from the Copernicus CAMS model at the centre of the perimeter; these are not measurements in each town. The pale bar is the worst hour, the solid one the daily average.

Open-Meteo.com (CC BY 4.0) · Copernicus Atmosphere Monitoring Service (CAMS)

Detections table · 42Every satellite heat detection, one by one, with time, satellite, power and coordinates.
⬇ Download CSV Times in UTC. Each detection is a 375 m pixel: a large fire yields hundreds per pass.
Date and timeSatelliteFRP (MW)LatLon

Other fires nearby

All fires in United Kingdom ›

Frequently asked questions

How long did the Highland fire last?
Copernicus dates it between 15 April 2018 and 15 April 2018: 1 day between the first and last image with fire.
How much area did it burn?
The perimeter Copernicus measured from satellite imagery is 2,755 hectares (27.6 km²). Official national figures may differ.
Which municipalities burned?
The fire only entered Highland (2,810 ha, 0.1 %).
What was the weather like?
During the fire the temperature reached 14.4 °C, humidity dropped to 55 % and gusts hit 44 km/h. The fire danger index (FWI) reached 4, class Very low.
Where does this data come from?
From the EFFIS (Copernicus) burnt perimeter, NASA FIRMS VIIRS hotspots and the administrative boundaries of United Kingdom (geoBoundaries). It is not an official report.

Where to verify it

A satellite detection is not an official report. Final figures and the fire’s status are published by each country’s emergency service.

Emergency number: 999 · 112 · Emergency number and official warnings ›

Satellite cross-check

History of this page Changes in area, dates, name, official record or merged pages, compared every night since 24 October 2026.

No changes since 24 October 2026.

RSS Changes to this page

Does something look wrong on this page?

This page is built from satellite data and official records, and it sometimes gets things wrong: the wrong dates, the wrong town, two fires merged into one, or something that was not a wildfire at all. If you know this fire first-hand (you live nearby, saw it, fought it or reported on it), tell us what really happened and we will check it.

Report an error
What do you think is wrong?

We will only use your email to reply about this report. Privacy. This is not an emergency service: if there is a fire now, call 999 · 112.

How we know this
  • Perimeter: EFFIS (Copernicus), mapped on satellite imagery; 2 polygons grouped in this page.
  • Dates from the perimeter: the VIIRS detections inside it did not change them. 42 Suomi-NPP VIIRS detections on those dates.
  • We have not matched this page with any official record.
  • Weather: Copernicus ERA5 reanalysis at the fire location, in cells of about 25 km.

How we build fire pages: methodology ›

Where this data comes from

The perimeter and land cover come from the Copernicus European Forest Fire Information System (EFFIS), measured on MODIS and Sentinel-2 imagery and published under CC BY 4.0. Heat detections come from the VIIRS sensors aboard Suomi-NPP and NOAA-20, distributed by NASA FIRMS at 375 m resolution. Municipal boundaries come from geoBoundaries ADM3 (Open Government Licence v3.0). The area per municipality is computed by WorldFires by crossing the perimeter with those boundaries, so it may differ slightly from each country’s official figure.