Burned area
satellite only5,660ha
Perimeter published by GWIS (Copernicus).
- Source
- GWIS (Copernicus)
- Date
- 14 Oct 2024 – 18 Oct 2024
+− cross-check
No official record is matched to this page to compare it with.
AU · Australia · –
East Pilbara fire, October 2024 East Pilbara
Out · last detection 18 Oct 2024, 17:04 UTC
The fire started on 14 October 2024 in East Pilbara, Australia, and satellites saw it burning for 5 days. Copernicus’s global GWIS system rebuilt a burnt perimeter of 5,660 hectares from heat detections, spread across a single municipality.
This entry is probably a savanna fire in Australia’s tropical north, not a bushfire like those in the south of the country. Millions of hectares of northern savanna and grassland burn every year: much of it in burns lit on purpose early in the dry season (traditional fire management, parks and cattle stations), the rest in grass fires that return to the same ground every few years. This is our assumption, based on the location; it is not confirmed. That is why it is left out of the wildfire rankings.
Use this data
Compare with…
Use this data
Fire page data · version 2026-10-24matches the official recordwith caveatssatellite onlymodel
When copying, the sentence is
Tick the figures you want: they make up the lede and the CSV.
Duration by satellite
satellite only5days
14 Oct 2024 to 18 Oct 2024: first and last day with fire on the page.
- Source
- GWIS (Copernicus) · NASA FIRMS · VIIRS
- Date
- last detection: 18 Oct 2024, 17:04 UTC
+− cross-check
Satellites pass a few times a day and cloud or smoke can hide the fire: a lack of detections is not an official extinction. Each country’s emergency service declares a fire contained or out.
Start
satellite only14 Oct 2024
First day with fire seen by the satellites or the perimeter.
- Source
- GWIS (Copernicus) · NASA FIRMS · VIIRS
- Date
- 14 Oct 2024
+− cross-check
No official record is matched to this page, so the alert time and the cause are not known here.
Hotspots
satellite only185
VIIRS detections at 375 m. Most intense hotspot: 201 MW.
- Source
- NASA FIRMS · VIIRS (Suomi NPP)
- Date
- 14 Oct 2024 – 18 Oct 2024
+− cross-check
There is no official record to compare with. Each hotspot is a pixel detected in one satellite pass, not a separate fire.
The worst day
satellite only1,212MW
Total radiative power on 15 October 2024; hotspots that day: 59.
- Source
- NASA FIRMS · VIIRS (FRP)
- Date
- 15 Oct 2024
+− cross-check
Fire radiative power (FRP) measures the energy the fire gives off when the satellite passes. Added up by day, it compares intensity, not area.
Danger at the start
model46.3FWI · very high
Fire Weather Index (Canadian system) computed by WorldFires for the day the fire started. Consecutive days without rain before: 11.
- Source
- WorldFires calculation (Canadian FWI system)
- Date
- 14 Oct 2024, local noon
- Model
- ERA5 0,25° (ECMWF · Copernicus C3S) · Open-Meteo.com
+− cross-check
This is an index computed from weather model data, not a measurement of the fire nor an official warning. Danger warnings are issued by each country’s authority. Emergency number and official warnings
Weather during the fire
model39.0°C · 12% RH
High of 39.0 °C and minimum humidity of 12% on 15 October 2024; gusts of 66 km/h on 16 October 2024.
- Source
- weather model at the fire’s grid cell
- Date
- 14 Oct 2024 – 18 Oct 2024
- Model
- ERA5 0,25° (ECMWF · Copernicus C3S) · Open-Meteo.com
+− cross-check
These are model values for a cell of about 25 km, not from a weather station: they may differ from what was measured on the ground.
This page’s change log has been kept since 24 October 2026: every night what it publishes is compared and the difference is logged. Anything earlier is reconstructed from each source’s date and marked as reconstructed.
Show
-
· reconstructed weatherWeather and FWI computed from the ERA5 reanalysis
-
· reconstructed GHSLPopulation and built-up area computed
What was saved on 24 October 2026
Every night a snapshot of what the page shows is saved. If anything changes, it appears in the list as a log entry.
- Area
- 5,660 ha
- Dates
- 14 Oct 2024 – 18 Oct 2024
- Name
- East Pilbara
- Official record
- —
Versioned permanent link
https://worldfires.org/en/fire/east-pilbara-2024-10?v=2026-10-24A version keeps the area, dates, name and official record; the area as it was logged (changes under 2% are not logged). The map, hotspots and weather always show today’s data.
Citation
A lede of about 60 words figures only, no adjectives
CSV for this fire east-pilbara-2024-10.csv · daily, no individual hotspots
| fecha | focos_viirs | frp_mw | tmax_c | tmin_c | hr_min_pct | viento_max_kmh | racha_max_kmh | precip_mm | fwi | clase_fwi | dentro_del_incendio |
|---|---|---|---|---|---|---|---|---|---|---|---|
| 2024-10-14 | 43 | 694 | 38.7 | 23.5 | 15 | 20.5 | 32.8 | 0 | 46.3 | muy_alto | 1 |
| 2024-10-15 | 59 | 1,212 | 39 | 24.7 | 12 | 19.1 | 36.4 | 0 | 53.4 | extremo | 1 |
| 2024-10-16 | 31 | 182 | 37 | 23.9 | 12 | 38.1 | 65.9 | 0 | 111.6 | muy_extremo | 1 |
| 2024-10-17 | 38 | 406 | 32.7 | 21.8 | 20 | 23.9 | 42.1 | 0 | 45.5 | muy_alto | 1 |
| 2024-10-18 | 14 | 410 | 35.1 | 19 | 14 | 23.7 | 44.3 | 0 | 57.7 | extremo | 1 |
| 2024-10-19 | 0 | 0 | 38.5 | 20.6 | 16 | 18.7 | 37.1 | 0 | 62.7 | extremo | 0 |
| 2024-10-20 | 0 | 0 | 39.4 | 23.7 | 14 | 16.5 | 31.3 | 0 | 55.8 | extremo | 0 |
| 2024-10-21 | 0 | 0 | 40.4 | 26.3 | 16 | 19.7 | 37.1 | 0 | 55.4 | extremo | 0 |
| 2024-10-22 | 0 | 0 | 40.7 | 27 | 16 | 17.4 | 34.9 | 0 | 57.9 | extremo | 0 |
| 2024-10-23 | 0 | 0 | 39.1 | 27.6 | 22 | 26.9 | 46.8 | 0.4 | 69.4 | extremo | 0 |
| 2024-10-24 | 0 | 0 | 38.3 | 27.4 | 24 | 26.8 | 50 | 0 | 84.3 | muy_extremo | 0 |
| 2024-10-25 | 0 | 0 | 39.5 | 25.4 | 18 | 19.3 | 35.6 | 0 | 57.6 | extremo | 0 |
| 2024-10-26 | 0 | 0 | 41 | 25.4 | 13 | 11.9 | 25.9 | 0 | 50.4 | extremo | 0 |
| 2024-10-27 | 0 | 0 | 40.5 | 26.5 | 12 | 26.6 | 47.9 | 0 | 76.1 | muy_extremo | 0 |
| 2024-10-28 | 0 | 0 | 39.8 | 25.4 | 24 | 26.1 | 45 | 1.2 | 63.2 | extremo | 0 |
It is generated in your browser from this page’s data: one file per fire, aggregated by day and without individual hotspots.
Live widget for your story
It updates itself while the fire is still active and links to this page. Free, with the attribution shown at the bottom.
Sources for this page: GWIS (Copernicus), NASA FIRMS (VIIRS), ERA5 (ECMWF/Copernicus C3S) · Open-Meteo.com (CC BY 4.0), GHSL (JRC). Open-Meteo.com · How we build fire pages: methodology
- Burnt area
- 5,660ha
- GWIS perimeter (Copernicus)
- Duration
- 5days
- 14 Oct 2024 – 18 Oct 2024
- Municipalities hit
- 1
- local government areas
- Started on
- 14 Oct
- 2024
- Heat detections
- 185
- in a single hotspot: 201 MW
- Danger at start
- 46
- Very high · FWI index
- Average daily power
- 581MW
- detected power per day, on average
Where it burned
HOTSPOTS BY DAY
14 Oct18 Oct
18 Oct 2024
How it evolved, day by day
14 Oct
15 Oct
16 Oct
17 Oct
18 Oct
Fire radiative power detected each day, in megawatts, and number of hotspots. The magenta bar marks the peak day.
The weather it burned in
39°high
66km/h · peak gust
12%lowest humidity
It had gone 11 days without rain (1 mm or more) when it started. Rain came after the fire: 1.2 mm on 28 Oct.
This area had burned before
0% of the perimeter overlaps earlier fires recorded since 2016: 4 ha in 2019.
How big is it?
London boundary: geoBoundaries · Office for National Statistics (Open Government Licence v3.0).
Paris boundary: geoBoundaries · Institut national de l'information géographique et forestière (IGN-F) (Etalab Open License 2.0).
Madrid boundary: geoBoundaries · Open Data ESRI, IGN Central Registry of Cartography Area (CC BY 4.0).
Berlin boundary: geoBoundaries · Federal Agency for Cartography and Geodesy (dl-de/by-2-0).
This compares size, not location: both shapes are at the same scale, north up, centred on each other.
What happened to each town
-
East Pilbara where it started5,693 ha reached on 14 Oct0.0 %
Burnt area inside each municipality, from crossing the GWIS perimeter with administrative boundaries. The distance runs from the point marking the centre of each area to the nearest fire: staying a kilometre away does not mean it reached the houses.
People and buildings inside the perimeter
GHSL 2025Built-up area< 0.1 ha
Residents< 20
Inside the perimeter there was no noticeable built-up land and almost nobody lived there (GHSL 2025, satellite-based estimate).
This is an estimate on 100 m cells, made from satellite imagery and census data: it does not mean that homes burned or that anyone was harmed. The perimeter also contains land that never burned. The GHSL 2025 epoch is a projection made from 2020 and earlier data.
Source: Global Human Settlement Layer (GHS-BUILT-S and GHS-POP R2023A), European Commission Joint Research Centre (JRC), © European Union, CC BY 4.0. Sum inside the perimeter computed by WorldFires. human-settlement.emergency.copernicus.eu
The weather day by day
ECMWF ERA5 reanalysis at the fire location, the standard reference for past weather, and the Canadian Fire Weather Index (the same system Copernicus uses), computed by WorldFires from that data. Days after the fire run until the first rain.
Open-Meteo.com (CC BY 4.0) · Copernicus Climate Change Service (ERA5)
| Day | High | Min. humidity | Peak gust | Rain | Danger (FWI) |
|---|---|---|---|---|---|
| 14 Oct | 38.7 °C | 15 % | 33 km/h | 0.0 mm | Very high 46 |
| 15 Oct | 39.0 °C | 12 % | 36 km/h | 0.0 mm | Extreme 53 |
| 16 Oct | 37.0 °C | 12 % | 66 km/h | 0.0 mm | Very extreme 112 |
| 17 Oct | 32.7 °C | 20 % | 42 km/h | 0.0 mm | Very high 46 |
| 18 Oct | 35.1 °C | 14 % | 44 km/h | 0.0 mm | Extreme 58 |
| 19 Oct after | 38.5 °C | 16 % | 37 km/h | 0.0 mm | Extreme 63 |
| 20 Oct after | 39.4 °C | 14 % | 31 km/h | 0.0 mm | Extreme 56 |
| 21 Oct after | 40.4 °C | 16 % | 37 km/h | 0.0 mm | Extreme 55 |
| 22 Oct after | 40.7 °C | 16 % | 35 km/h | 0.0 mm | Extreme 58 |
| 23 Oct after | 39.1 °C | 22 % | 47 km/h | 0.4 mm | Extreme 69 |
| 24 Oct after | 38.3 °C | 24 % | 50 km/h | 0.0 mm | Very extreme 84 |
| 25 Oct after | 39.5 °C | 18 % | 36 km/h | 0.0 mm | Extreme 58 |
| 26 Oct after | 41.0 °C | 13 % | 26 km/h | 0.0 mm | Extreme 50 |
| 27 Oct after | 40.5 °C | 12 % | 48 km/h | 0.0 mm | Very extreme 76 |
| 28 Oct after | 39.8 °C | 24 % | 45 km/h | 1.2 mm | Extreme 63 |
Its twins: fires that started in the same weather
It started with an FWI of 46.3, a minimum humidity of 15% and 11 days without rain. Fires in the area that started in weather like this since 2017: 1.
FWI at the start
46.3
Minimum humidity
15 %
Days without rain
11
this fire
chosen twins
rest of the area
Almost identicalSimilar
Outlines of the closest twins
This fire · East Pilbara fire, October 2024
5,660 ha
5 days
FWI 46.3
Min. humidity 15 %
Wiluna fire, January 2019
5,435 ha
4 days
FWI 52.0
Min. humidity 10 %
230 km away, in 2019
First rain (1 mm or more) after it ended: 1.1 mm on 23 Jan.
What happened to them
Fires in the area that started in similar weather: 1. With fewer than 15 we give no figures: they would be more noise than signal.
This is a bank of analogues: it shows what usually happens, not what will happen. With fewer than 15 twins we give no figures. How we calculate it
How it ended
1.2 mmfirst rain
28 Oct10 days after it ended
66km/h · max. gust
It was considered over on 18 Oct, and on 28 Oct 1.2 mm fell. We do not know whether the rain or the firefighters put it out.
Weather on this page: Open-Meteo.com (CC BY 4.0) · Copernicus Climate Change Service (ERA5)
How a twin is chosen
- Same area: fires that have already ended, less than 250 km from this one, since 2017.
- Same start: we compare the FWI on the first day, the minimum humidity that day and the run of days without rain before it. The slider sets how much they may differ.
- Only pages with final weather data (ERA5 reanalysis) calculated in the same way as this fire’s; agricultural and grass burns and pages with data under review are left out.
- Fires burning at the same time as this one (a week before or after) are left out: they share the same spell of weather and do not count as a precedent.
- They are sorted by similarity, and the outlines of the first five are drawn.
Before and after, from space
Drag the line to compare the same ground before the fire and after it.
↔
Before · 7 Oct 2024
After · 25 Oct 2024
Sentinel-2 did not pass over on that day. Try another date, or use false colour, which is daily.
If the day is cloudy, change the date: each satellite passes once a day. In false colour the burnt ground looks brown or red.
The smoke
CAMS · CopernicusOn 18 October 2024 the air beside the fire reached 29 µg/m³ of PM2.5, but no daily average passed the WHO guideline (15).
PM2.5 peak29 µg/m³
Days over the guideline0 days
PM1043 µg/m³
Optical depth0.19
WHO 15
12 Oct14 Oct16 Oct18 Oct20 Oct
Good
Fair
Moderate
Poor
Very poor
Extremely poor
Particles from the Copernicus CAMS model at the centre of the perimeter; these are not measurements in each town. The pale bar is the worst hour, the solid one the daily average.
Open-Meteo.com (CC BY 4.0) · Copernicus Atmosphere Monitoring Service (CAMS)
Detections table · 185Every satellite heat detection, one by one, with time, satellite, power and coordinates.
⬇ Download CSV
Times in UTC. Each detection is a 375 m pixel: a large fire yields hundreds per pass.
| Date and time | Satellite | FRP (MW) | Lat | Lon |
|---|
Other fires nearby
Frequently asked questions
- How long did the East Pilbara fire last?
- GWIS (Copernicus) dates it between 14 October 2024 and 18 October 2024: 5 days between the first and last heat detection of the perimeter.
- How much area did it burn?
- The perimeter GWIS (Copernicus) rebuilt from heat detections is 5,660 hectares (56.6 km²). It is an estimate: official national figures may differ.
- Which municipalities burned?
- The fire only entered East Pilbara (5,693 ha, 0.0 %).
- What was the weather like?
- During the fire the temperature reached 39.0 °C, humidity dropped to 12 % and gusts hit 66 km/h. The fire danger index (FWI) reached 112, class Very extreme.
- Where does this data come from?
- From the GWIS (Copernicus) burnt perimeter, NASA FIRMS VIIRS hotspots and the administrative boundaries of Australia (geoBoundaries). It is not an official report.
Where to verify it
A satellite detection is not an official report. Final figures and the fire’s status are published by each country’s emergency service.
Emergency number: 000 · Emergency number and official warnings
Satellite cross-check
History of this page Changes in area, dates, name, official record or merged pages, compared every night since 24 October 2026.
No changes since 24 October 2026.
RSS Changes to this page With cross-checks and a citable version
Does something look wrong on this page?
This page is built from satellite data and official records, and it sometimes gets things wrong: the wrong dates, the wrong town, two fires merged into one, or something that was not a wildfire at all. If you know this fire first-hand (you live nearby, saw it, fought it or reported on it), tell us what really happened and we will check it.
Report an error
How we know this
- Perimeter: GWIS (Copernicus), rebuilt from heat detections rather than mapped on imagery.
- Dates from the perimeter: the VIIRS detections inside it did not change them. 185 Suomi-NPP VIIRS detections on those dates.
- We have not matched this page with any official record.
- Weather: Copernicus ERA5 reanalysis at the fire location, in cells of about 25 km.
- Built-up area and population come from the JRC Global Human Settlement Layer (epoch 2025, 100 m cells), summed inside the perimeter: an estimate of what was there, not a damage count.
- Probably a vegetation burn: not counted in the totals.
Where this data comes from
The perimeter comes from the Copernicus Global Wildfire Information System (GWIS), which rebuilds it from MODIS and VIIRS heat detections and publishes it under CC BY 4.0. It is not measured on imagery as in Europe, so it is an estimate. Heat detections come from the VIIRS sensors aboard Suomi-NPP and NOAA-20, distributed by NASA FIRMS at 375 m resolution. Municipal boundaries come from geoBoundaries ADM2 (Creative Commons Attribution 4.0 International (CC BY 4.0)). The area per municipality is computed by WorldFires by crossing the perimeter with those boundaries, so it may differ from each country’s official figure.