Chouf fire, October 2019 Chouf
The fire started on 14 October 2019 in Chouf, Lebanon, and satellites saw it burning for 2 days. Copernicus mapped a burnt perimeter of 267 hectares from satellite imagery, spread across a single municipality.
Number 2 in Lebanon in 2019, of 4.
The power measured by the satellite is low (9.3 MW in the strongest hotspot), more typical of grass or stubble burning, or a slow surface fire, than of a large crown fire.
Compare with…
Suggestions: Aley · 2019Chouf · 2025Chouf · 2023Chouf · 2024
- Burnt area
- 267ha
- Copernicus perimeter
- Duration
- 2days
- 14 Oct 2019 – 15 Oct 2019
- Municipalities hit
- 1
- districts
- Started on
- 14 Oct
- 2019
- Heat detections
- 3
- in a single hotspot: 9 MW
- Danger at start
- 37
- High · FWI index
- Average daily power
- 10MW
- detected power per day, on average
Where it burned
How it evolved, day by day
Fire radiative power detected each day, in megawatts, and number of hotspots. The magenta bar marks the peak day.
The weather it burned in
It had gone 11 days without rain (1 mm or more) when it started. Rain came after the fire: 1.6 mm on 17 Oct.
This area had burned before
No earlier perimeters overlap this fire since 2016, when the satellite record begins.
What happened to each town
-
Chouf where it started267 ha reached on 14 Oct0.6 %
Burnt area inside each municipality, from crossing the official perimeter with administrative boundaries. The distance runs from the point marking the centre of each area to the nearest fire: staying a kilometre away does not mean it reached the houses.
What burned
- Coniferous forest58 %
- Other natural land15 %
- Mixed forest11 %
- Artificial surfaces11 %
- Agricultural areas4.9 %
Land cover inside the perimeter as reported by Copernicus EFFIS (outside the Corine Land Cover area).
People and buildings inside the perimeter
GHSL 2020Inside the perimeter there were about 7.5 hectares of built-up land and about 80 residents (GHSL 2020, satellite-based estimate).
This is an estimate on 100 m cells, made from satellite imagery and census data: it does not mean that homes burned or that anyone was harmed. The perimeter also contains land that never burned.
Source: Global Human Settlement Layer (GHS-BUILT-S and GHS-POP R2023A), European Commission Joint Research Centre (JRC), © European Union, CC BY 4.0. Sum inside the perimeter computed by WorldFires. human-settlement.emergency.copernicus.eu
The weather day by day
ECMWF ERA5 reanalysis at the fire location, the standard reference for past weather, and the Canadian Fire Weather Index (the same system Copernicus uses), computed by WorldFires from that data. Days after the fire run until the first rain.
Open-Meteo.com (CC BY 4.0) · Copernicus Climate Change Service (ERA5)
| Day | High | Min. humidity | Peak gust | Rain | Danger (FWI) |
|---|---|---|---|---|---|
| 14 Oct | 35.2 °C | 20 % | 30 km/h | 0.4 mm | High 37 |
| 15 Oct | 35.1 °C | 20 % | 35 km/h | 0.2 mm | Very high 40 |
| 16 Oct after | 31.7 °C | 36 % | 34 km/h | 0.3 mm | High 36 |
| 17 Oct after | 27.8 °C | 63 % | 35 km/h | 1.6 mm | Low 9 |
Before and after, from space
Drag the line to compare the same ground before the fire and after it.
If the day is cloudy, change the date: each satellite passes once a day. In false colour the burnt ground looks brown or red.
Detections table · 3Every satellite heat detection, one by one, with time, satellite, power and coordinates.
| Date and time | Satellite | FRP (MW) | Lat | Lon |
|---|
Other fires nearby
Frequently asked questions
- How long did the Chouf fire last?
- Copernicus dates it between 14 October 2019 and 15 October 2019: 2 days between the first and last image with fire.
- How much area did it burn?
- The perimeter Copernicus measured from satellite imagery is 267 hectares (2.7 km²). Official national figures may differ.
- Which municipalities burned?
- The fire only entered Chouf (267 ha, 0.6 %).
- What was the weather like?
- During the fire the temperature reached 35.2 °C, humidity dropped to 20 % and gusts hit 35 km/h. The fire danger index (FWI) reached 40, class Very high.
- Where does this data come from?
- From the EFFIS (Copernicus) burnt perimeter, NASA FIRMS VIIRS hotspots and the administrative boundaries of Lebanon (geoBoundaries). It is not an official report.
Where to verify it
A satellite detection is not an official report. Final figures and the fire’s status are published by each country’s emergency service.
Satellite cross-check
History of this page Changes in area, dates, name, official record or merged pages, compared every night since 24 October 2026.
No changes since 24 October 2026.
Does something look wrong on this page?
This page is built from satellite data and official records, and it sometimes gets things wrong: the wrong dates, the wrong town, two fires merged into one, or something that was not a wildfire at all. If you know this fire first-hand (you live nearby, saw it, fought it or reported on it), tell us what really happened and we will check it.
Report an error
How we know this
- Perimeter: EFFIS (Copernicus), mapped on satellite imagery.
- Dates from the perimeter: the VIIRS detections inside it did not change them. 3 Suomi-NPP VIIRS detections on those dates.
- We have not matched this page with any official record.
- Weather: Copernicus ERA5 reanalysis at the fire location, in cells of about 25 km.
- Built-up area and population come from the JRC Global Human Settlement Layer (epoch 2020, 100 m cells), summed inside the perimeter: an estimate of what was there, not a damage count.
Where this data comes from
The perimeter and land cover come from the Copernicus European Forest Fire Information System (EFFIS), measured on MODIS and Sentinel-2 imagery and published under CC BY 4.0. Heat detections come from the VIIRS sensors aboard Suomi-NPP and NOAA-20, distributed by NASA FIRMS at 375 m resolution. Municipal boundaries come from geoBoundaries ADM2 (Public Domain). The area per municipality is computed by WorldFires by crossing the perimeter with those boundaries, so it may differ slightly from each country’s official figure.