Chegutu fire, 23 August 2026 Chegutu
The fire started on 23 August 2026 in Chegutu, Zimbabwe, and satellites saw it burning for 2 days. Copernicus’s global GWIS system rebuilt a burnt perimeter of 1,042 hectares from heat detections, spread across a single municipality.
It is the 747th largest in Mashonaland West since 2016 (of 823 with a page). Number 328 in Zimbabwe in 2026, of 370.
The power measured by the satellite is low (11.9 MW in the strongest hotspot), more typical of grass or stubble burning, or a slow surface fire, than of a large crown fire.
- Burnt area
- 1,042ha
- GWIS perimeter (Copernicus)
- Duration
- 2days
- 23 Aug 2026 – 24 Aug 2026
- Municipalities hit
- 1
- districts
- Started on
- 23 Aug
- 2026
- Heat detections
- 17
- in a single hotspot: 12 MW
- Danger at start
- 48
- Very high · FWI index
- Energy released
- 115MW
- sum of detected power
Where it burned
How it evolved, day by day
Fire radiative power detected each day, in megawatts, and number of hotspots. The magenta bar marks the peak day.
The weather it burned in
It had gone more than two months without rain (1 mm or more) when it started.
This area had burned before
No earlier perimeters overlap this fire since 2016, when the satellite record begins.
What happened to each town
-
Chegutu where it started1,047 ha reached on 23 Aug0.2 %
Burnt area inside each municipality, from crossing the GWIS perimeter with administrative boundaries. The distance is from the town centre to the nearest fire: staying a kilometre away does not mean it reached the houses.
The weather day by day
ECMWF ERA5 reanalysis at the fire location, the standard reference for past weather, and the Canadian Fire Weather Index (the same system Copernicus uses), computed by WorldFires from that data. Days after the fire run until the first rain.
Open-Meteo.com (CC BY 4.0) · Copernicus Climate Change Service (ERA5)
| Day | High | Min. humidity | Peak gust | Rain | Danger (FWI) |
|---|---|---|---|---|---|
| 23 Aug | 29.4 °C | 16 % | 37 km/h | 0.0 mm | Very high 48 |
| 24 Aug | 27.6 °C | 21 % | 40 km/h | 0.0 mm | Very high 47 |
| 25 Aug after | 27.7 °C | 14 % | 26 km/h | 0.0 mm | Very high 43 |
| 26 Aug after | 28.8 °C | 16 % | 33 km/h | 0.0 mm | Very high 46 |
| 27 Aug after | 26.0 °C | 19 % | 45 km/h | 0.0 mm | Extreme 50 |
| 28 Aug after | 24.5 °C | 25 % | 42 km/h | 0.0 mm | Very high 45 |
| 29 Aug after | 25.3 °C | 29 % | 35 km/h | 0.0 mm | High 38 |
| 30 Aug after | 27.6 °C | 28 % | 35 km/h | 0.0 mm | Very high 39 |
| 31 Aug after | 28.9 °C | 26 % | 40 km/h | 0.0 mm | Very high 42 |
| 1 Sept after | 28.9 °C | 24 % | 39 km/h | 0.0 mm | Very high 41 |
| 2 Sept after | 28.1 °C | 27 % | 34 km/h | 0.0 mm | Very high 39 |
| 3 Sept after | 28.9 °C | 27 % | 46 km/h | 0.0 mm | Very high 45 |
Before and after, from space
Drag the line to compare the same ground before the fire and after it.
If the day is cloudy, change the date: each satellite passes once a day. In false colour the burnt ground looks brown or red.
The smoke
CAMS · CopernicusOn 25 August 2026 the air beside the fire reached 44 µg/m³ of PM2.5. That day averaged 30: 2.0 times the WHO daily guideline (15).
Particles from the Copernicus CAMS model at the centre of the perimeter; these are not measurements in each town. The pale bar is the worst hour, the solid one the daily average.
Open-Meteo.com (CC BY 4.0) · Copernicus Atmosphere Monitoring Service (CAMS)
Detections table · 17Every satellite heat detection, one by one, with time, satellite, power and coordinates.
| Date and time | Satellite | FRP (MW) | Lat | Lon |
|---|
Other fires nearby
Frequently asked questions
- How long did the Chegutu fire last?
- GWIS (Copernicus) dates it between 23 August 2026 and 24 August 2026: 2 days between the first and last heat detection of the perimeter.
- How much area did it burn?
- The perimeter GWIS (Copernicus) rebuilt from heat detections is 1,042 hectares (10.4 km²). It is an estimate: official national figures may differ.
- Which municipalities burned?
- The fire only entered Chegutu (1,047 ha, 0.2 %).
- What was the weather like?
- During the fire the temperature reached 29.4 °C, humidity dropped to 16 % and gusts hit 40 km/h. The fire danger index (FWI) reached 48, class Very high.
- Where does this data come from?
- From the GWIS (Copernicus) burnt perimeter, NASA FIRMS VIIRS hotspots and the administrative boundaries of Zimbabwe (geoBoundaries). It is not an official report.
Where to verify it
A satellite detection is not an official report. Final figures and the fire’s status are published by each country’s emergency service.
Satellite cross-check
Does something look wrong on this page?
This page is built from satellite data and official records, and it sometimes gets things wrong: the wrong dates, the wrong town, two fires merged into one, or something that was not a wildfire at all. If you know this fire first-hand (you live nearby, saw it, fought it or reported on it), tell us what really happened and we will check it.
Report an error
Where this data comes from
The perimeter comes from the Copernicus Global Wildfire Information System (GWIS), which rebuilds it from MODIS and VIIRS heat detections and publishes it under CC BY 4.0. It is not measured on imagery as in Europe, so it is an estimate. Heat detections come from the VIIRS sensors aboard Suomi-NPP and NOAA-20, distributed by NASA FIRMS at 375 m resolution. Municipal boundaries come from geoBoundaries ADM2 (Creative Commons Attribution 3.0 Intergovernmental Organisations (CC BY 3.0 IGO)). The area per municipality is computed by WorldFires by crossing the perimeter with those boundaries, so it may differ from each country’s official figure.