Burke fire, November 2022 Burke
The fire started on 16 November 2022 in Burke, Australia, and satellites saw it burning for 4 days. Copernicus’s global GWIS system rebuilt a burnt perimeter of 5,528 hectares from heat detections, spread across a single municipality.
It is the 1532th largest in Queensland since 2016 (of 1737 with a page). Number 487 in Australia in 2022, of 566.
The power measured by the satellite is low (19.2 MW in the strongest hotspot), more typical of grass or stubble burning, or a slow surface fire, than of a large crown fire.
- Burnt area
- 5,528ha
- GWIS perimeter (Copernicus)
- Duration
- 4days
- 16 Nov 2022 – 19 Nov 2022
- Municipalities hit
- 1
- local government areas
- Started on
- 16 Nov
- 2022
- Heat detections
- 150
- in a single hotspot: 19 MW
- Danger at start
- 39
- Very high · FWI index
- Energy released
- 684MW
- sum of detected power
Where it burned
How it evolved, day by day
Fire radiative power detected each day, in megawatts, and number of hotspots. The magenta bar marks the peak day.
The weather it burned in
It had gone 0 days without rain (1 mm or more) when it started. Rain came after the fire: 2.1 mm on 20 Nov.
This area had burned before
48% of the perimeter overlaps earlier fires recorded since 2016: 73 ha in 2016, 1,421 ha in 2017, 1,366 ha in 2018, 243 ha in 2021. Part of it burned more than once, so the yearly figures add up to more than the 2,663 ha that had burned before.
What happened to each town
-
Burke where it started5,532 ha reached on 16 Nov0.1 %
Burnt area inside each municipality, from crossing the GWIS perimeter with administrative boundaries. The distance is from the town centre to the nearest fire: staying a kilometre away does not mean it reached the houses.
The weather day by day
ECMWF ERA5 reanalysis at the fire location, the standard reference for past weather, and the Canadian Fire Weather Index (the same system Copernicus uses), computed by WorldFires from that data. Days after the fire run until the first rain.
Open-Meteo.com (CC BY 4.0) · Copernicus Climate Change Service (ERA5)
| Day | High | Min. humidity | Peak gust | Rain | Danger (FWI) |
|---|---|---|---|---|---|
| 16 Nov | 38.8 °C | 17 % | 44 km/h | 0.0 mm | Very high 39 |
| 17 Nov | 39.9 °C | 12 % | 42 km/h | 0.0 mm | Very high 45 |
| 18 Nov | 40.5 °C | 13 % | 38 km/h | 0.0 mm | Very high 44 |
| 19 Nov | 39.2 °C | 33 % | 45 km/h | 0.5 mm | Very high 40 |
| 20 Nov after | 39.0 °C | 32 % | 33 km/h | 2.1 mm | High 23 |
Before and after, from space
Drag the line to compare the same ground before the fire and after it.
If the day is cloudy, change the date: each satellite passes once a day. In false colour the burnt ground looks brown or red.
The smoke
CAMS · CopernicusOn 17 November 2022 the air beside the fire reached 90 µg/m³ of PM2.5. That day averaged 35: 2.3 times the WHO daily guideline (15).
Particles from the Copernicus CAMS model at the centre of the perimeter; these are not measurements in each town. The pale bar is the worst hour, the solid one the daily average.
Open-Meteo.com (CC BY 4.0) · Copernicus Atmosphere Monitoring Service (CAMS)
Detections table · 150Every satellite heat detection, one by one, with time, satellite, power and coordinates.
| Date and time | Satellite | FRP (MW) | Lat | Lon |
|---|
Other fires nearby
Frequently asked questions
- How long did the Burke fire last?
- GWIS (Copernicus) dates it between 16 November 2022 and 19 November 2022: 4 days between the first and last heat detection of the perimeter.
- How much area did it burn?
- The perimeter GWIS (Copernicus) rebuilt from heat detections is 5,528 hectares (55.3 km²). It is an estimate: official national figures may differ.
- Which municipalities burned?
- The fire only entered Burke (5,532 ha, 0.1 %).
- What was the weather like?
- During the fire the temperature reached 40.5 °C, humidity dropped to 12 % and gusts hit 45 km/h. The fire danger index (FWI) reached 45, class Very high.
- Where does this data come from?
- From the GWIS (Copernicus) burnt perimeter, NASA FIRMS VIIRS hotspots and the administrative boundaries of Australia (geoBoundaries). It is not an official report.
Where to verify it
A satellite detection is not an official report. Final figures and the fire’s status are published by each country’s emergency service.
Emergency number: 000
Satellite cross-check
Does something look wrong on this page?
This page is built from satellite data and official records, and it sometimes gets things wrong: the wrong dates, the wrong town, two fires merged into one, or something that was not a wildfire at all. If you know this fire first-hand (you live nearby, saw it, fought it or reported on it), tell us what really happened and we will check it.
Report an error
Where this data comes from
The perimeter comes from the Copernicus Global Wildfire Information System (GWIS), which rebuilds it from MODIS and VIIRS heat detections and publishes it under CC BY 4.0. It is not measured on imagery as in Europe, so it is an estimate. Heat detections come from the VIIRS sensors aboard Suomi-NPP and NOAA-20, distributed by NASA FIRMS at 375 m resolution. Municipal boundaries come from geoBoundaries ADM2 (Creative Commons Attribution 4.0 International (CC BY 4.0)). The area per municipality is computed by WorldFires by crossing the perimeter with those boundaries, so it may differ from each country’s official figure.