Skip to content
worldfires
TR · Türkiye · →

Antakya fire, July 2018 Antakya

Out · last detection 17 Jul 2018, 00:36 UTC

The fire started on 16 July 2018 in Antakya, Türkiye, and satellites saw it burning for 2 days. Copernicus mapped a burnt perimeter of 233 hectares from satellite imagery, spread across a single municipality.

It is the 9th largest in Hatay since 2016 (of 18 with a page). Number 45 in Türkiye in 2018, of 104.

The power measured by the satellite is low (7.3 MW in the strongest hotspot), more typical of grass or stubble burning, or a slow surface fire, than of a large crown fire.

Burnt area
233ha
Copernicus perimeter
Duration
2days
16 Jul 2018 – 17 Jul 2018
Municipalities hit
1
districts
Started on
16 Jul
2018
Heat detections
11
in a single hotspot: 7 MW
Danger at start
32
High · FWI index
Energy released
47MW
sum of detected power

Where it burned

17 Jul 2018
HOTSPOTS BY DAY 16 Jul17 Jul

How it evolved, day by day

1617

Fire radiative power detected each day, in megawatts, and number of hotspots. The magenta bar marks the peak day.

The weather it burned in

33°high
40km/h · peak gust
31%lowest humidity

It had gone 24 days without rain (1 mm or more) when it started.

This area had burned before

No earlier perimeters overlap this fire since 2016, when the satellite record begins.

What happened to each town

  1. Antakya 377,793 inhabitants · 20.3 km from the town where it started
    233 ha reached on 16 Jul
    0.3 %

Burnt area inside each municipality, from crossing the official perimeter with administrative boundaries. The distance is from the town centre to the nearest fire: staying a kilometre away does not mean it reached the houses.

What burned

  • Coniferous forest49 %
  • Scrub and transitional woodland27 %
  • Agricultural areas14 %
  • Other natural land10 %

Land cover inside the perimeter according to Corine Land Cover, as reported by Copernicus.

The weather day by day

ECMWF ERA5 reanalysis at the fire location, the standard reference for past weather, and the Canadian Fire Weather Index (the same system Copernicus uses), computed by WorldFires from that data. Days after the fire run until the first rain.

Open-Meteo.com (CC BY 4.0) · Copernicus Climate Change Service (ERA5)

Day High Min. humidity Peak gust Rain Danger (FWI)
16 Jul 33.3 °C 31 % 39 km/h 0.0 mm High 32
17 Jul 33.0 °C 39 % 40 km/h 0.0 mm High 34
18 Jul after 32.6 °C 47 % 41 km/h 0.0 mm High 31
19 Jul after 31.4 °C 49 % 42 km/h 0.0 mm High 29
20 Jul after 30.8 °C 53 % 39 km/h 0.3 mm High 27
21 Jul after 32.2 °C 48 % 41 km/h 0.0 mm High 27
22 Jul after 32.3 °C 46 % 43 km/h 0.1 mm High 28
23 Jul after 33.3 °C 43 % 38 km/h 0.0 mm High 29
24 Jul after 32.8 °C 44 % 38 km/h 0.0 mm High 27
25 Jul after 33.3 °C 34 % 42 km/h 0.0 mm High 34
26 Jul after 30.7 °C 53 % 38 km/h 0.6 mm High 25
27 Jul after 30.5 °C 48 % 45 km/h 0.6 mm High 26

Before and after, from space

Drag the line to compare the same ground before the fire and after it.

Before · 9 Jul 2018
After · 24 Jul 2018

If the day is cloudy, change the date: each satellite passes once a day. In false colour the burnt ground looks brown or red.

The smoke

CAMS · Copernicus

On 16 July 2018 the air beside the fire reached 18 µg/m³ of PM2.5. That day averaged 16: 1.1 times the WHO daily guideline (15).

PM2.5 peak18 µg/m³
Days over the guideline1 day
PM1037 µg/m³
14151617181920
Good Fair Moderate Poor Very poor Extremely poor

Particles from the Copernicus CAMS model at the centre of the perimeter; these are not measurements in each town. The pale bar is the worst hour, the solid one the daily average.

Open-Meteo.com (CC BY 4.0) · Copernicus Atmosphere Monitoring Service (CAMS)

Detections table · 11Every satellite heat detection, one by one, with time, satellite, power and coordinates.
⬇ Download CSV Times in UTC. Each detection is a 375 m pixel: a large fire yields hundreds per pass.
Date and timeSatelliteFRP (MW)LatLon

Other fires nearby

All fires in Türkiye ›

Frequently asked questions

How long did the Antakya fire last?
Copernicus dates it between 16 July 2018 and 17 July 2018: 2 days between the first and last image with fire.
How much area did it burn?
The perimeter Copernicus measured from satellite imagery is 233 hectares (2.3 km²). Official national figures may differ.
Which municipalities burned?
The fire only entered Antakya (233 ha, 0.3 %).
Did the fire reach a town?
The closest fire to a town centre came within 20.3 km of Antakya. That is the distance to the perimeter or nearest hotspot; it does not mean it entered the houses.
What was the weather like?
During the fire the temperature reached 33.3 °C, humidity dropped to 31 % and gusts hit 40 km/h. The fire danger index (FWI) reached 34, class High.
Where does this data come from?
From the EFFIS (Copernicus) burnt perimeter, NASA FIRMS VIIRS hotspots and the administrative boundaries of Türkiye (geoBoundaries). It is not an official report.

Where to verify it

A satellite detection is not an official report. Final figures and the fire’s status are published by each country’s emergency service.

Emergency number: 112

Satellite cross-check

Does something look wrong on this page?

This page is built from satellite data and official records, and it sometimes gets things wrong: the wrong dates, the wrong town, two fires merged into one, or something that was not a wildfire at all. If you know this fire first-hand (you live nearby, saw it, fought it or reported on it), tell us what really happened and we will check it.

Report an error
What do you think is wrong?

We will only use your email to reply about this report. Privacy. This is not an emergency service: if there is a fire now, call 112.

Where this data comes from

The perimeter and land cover come from the Copernicus European Forest Fire Information System (EFFIS), measured on MODIS and Sentinel-2 imagery and published under CC BY 4.0. Heat detections come from the VIIRS sensors aboard Suomi-NPP and NOAA-20, distributed by NASA FIRMS at 375 m resolution. Municipal boundaries come from geoBoundaries ADM2 (Open Data Commons Open Database License 1.0). The area per municipality is computed by WorldFires by crossing the perimeter with those boundaries, so it may differ slightly from each country’s official figure.