Skip to content
worldfires
FR · France · →

Accous fire, February 2019 Accous

Out · last detection 19 Feb 2019, 12:32 UTC

The fire started on 19 February 2019 in Accous, France, and satellites saw it burning for 1 day. Copernicus mapped a burnt perimeter of 245 hectares from satellite imagery, spread across a single municipality.

This record is most likely a pastoral burn (écobuage) in the Pyrenees, not a forest fire. In winter, grassland and scrub are burnt to renew the pasture, and this fire does not appear in France's official forest fire database (BDIFF). That is why it is left out of the fire rankings.

The power measured by the satellite is low (17.0 MW in the strongest hotspot), more typical of grass or stubble burning, or a slow surface fire, than of a large crown fire.

Burnt area
245ha
Copernicus perimeter
Duration
1day
19 Feb 2019 – 19 Feb 2019
Municipalities hit
1
communes
Started on
19 Feb
2019
Heat detections
1
in a single hotspot: 17 MW
Danger at start
2
Very low · FWI index
Energy released
17MW
sum of detected power

Where it burned

HOTSPOTS BY DAY 19 Feb19 Feb

How it evolved, day by day

19

Fire radiative power detected each day, in megawatts, and number of hotspots. The magenta bar marks the peak day.

The weather it burned in

10°high
20km/h · peak gust
53%lowest humidity

It had gone 7 days without rain (1 mm or more) when it started.

This area had burned before

No earlier perimeters overlap this fire since 2016, when the satellite record begins.

What happened to each town

  1. Accous where it started
    245 ha reached on 19 Feb
    4.0 %

Burnt area inside each municipality, from crossing the official perimeter with administrative boundaries. The distance is from the town centre to the nearest fire: staying a kilometre away does not mean it reached the houses.

What burned

  • Other natural land89 %
  • Mixed forest4.9 %
  • Agricultural areas3.7 %
  • Broadleaved forest2.1 %

Natura 2000 protected area affected: 82 %

Natura 2000 sites (European Environment Agency, 2024 release) crossed by the perimeter.

Land cover inside the perimeter according to Corine Land Cover, as reported by Copernicus.

The weather day by day

ECMWF ERA5 reanalysis at the fire location, the standard reference for past weather, and the Canadian Fire Weather Index (the same system Copernicus uses), computed by WorldFires from that data. Days after the fire run until the first rain.

Open-Meteo.com (CC BY 4.0) · Copernicus Climate Change Service (ERA5)

Day High Min. humidity Peak gust Rain Danger (FWI)
19 Feb 10.5 °C 53 % 20 km/h 0.0 mm Very low 2
20 Feb after 11.8 °C 46 % 23 km/h 0.0 mm Very low 3
21 Feb after 13.9 °C 47 % 21 km/h 0.0 mm Very low 3
22 Feb after 14.4 °C 42 % 23 km/h 0.0 mm Very low 3
23 Feb after 14.5 °C 41 % 30 km/h 0.0 mm Very low 3
24 Feb after 14.6 °C 52 % 24 km/h 0.0 mm Very low 3
25 Feb after 15.7 °C 46 % 22 km/h 0.0 mm Very low 4
26 Feb after 17.9 °C 36 % 28 km/h 0.0 mm Very low 5
27 Feb after 20.0 °C 22 % 26 km/h 0.0 mm Low 7
28 Feb after 11.5 °C 60 % 32 km/h 0.0 mm Very low 5
1 Mar after 10.8 °C 64 % 28 km/h 0.0 mm Very low 3

Before and after, from space

Drag the line to compare the same ground before the fire and after it.

Before · 12 Feb 2019
After · 26 Feb 2019

If the day is cloudy, change the date: each satellite passes once a day. In false colour the burnt ground looks brown or red.

The smoke

CAMS · Copernicus

On 19 February 2019 the air beside the fire reached 40 µg/m³ of PM2.5. That day averaged 24: 1.6 times the WHO daily guideline (15).

PM2.5 peak40 µg/m³
Days over the guideline6 days
PM1055 µg/m³
171819202122232425262728123
Good Fair Moderate Poor Very poor Extremely poor

Particles from the Copernicus CAMS model at the centre of the perimeter; these are not measurements in each town. The pale bar is the worst hour, the solid one the daily average.

Open-Meteo.com (CC BY 4.0) · Copernicus Atmosphere Monitoring Service (CAMS)

Detections table · 1Every satellite heat detection, one by one, with time, satellite, power and coordinates.
⬇ Download CSV Times in UTC. Each detection is a 375 m pixel: a large fire yields hundreds per pass.
Date and timeSatelliteFRP (MW)LatLon

Other fires nearby

All fires in France ›

Frequently asked questions

How long did the Accous fire last?
Copernicus dates it between 19 February 2019 and 19 February 2019: 1 day between the first and last image with fire.
How much area did it burn?
The perimeter Copernicus measured from satellite imagery is 245 hectares (2.4 km²). Official national figures may differ.
Which municipalities burned?
The fire only entered Accous (245 ha, 4.0 %).
What was the weather like?
During the fire the temperature reached 10.5 °C, humidity dropped to 53 % and gusts hit 20 km/h. The fire danger index (FWI) reached 2, class Very low.
Where does this data come from?
From the EFFIS (Copernicus) burnt perimeter, NASA FIRMS VIIRS hotspots and the administrative boundaries of France (geoBoundaries). It is not an official report.

Where to verify it

A satellite detection is not an official report. Final figures and the fire’s status are published by each country’s emergency service.

Emergency number: 112 · 18

Satellite cross-check

Does something look wrong on this page?

This page is built from satellite data and official records, and it sometimes gets things wrong: the wrong dates, the wrong town, two fires merged into one, or something that was not a wildfire at all. If you know this fire first-hand (you live nearby, saw it, fought it or reported on it), tell us what really happened and we will check it.

Report an error
What do you think is wrong?

We will only use your email to reply about this report. Privacy. This is not an emergency service: if there is a fire now, call 112 · 18.

Where this data comes from

The perimeter and land cover come from the Copernicus European Forest Fire Information System (EFFIS), measured on MODIS and Sentinel-2 imagery and published under CC BY 4.0. Heat detections come from the VIIRS sensors aboard Suomi-NPP and NOAA-20, distributed by NASA FIRMS at 375 m resolution. Municipal boundaries come from geoBoundaries ADM5 (Open Data Commons Attribution License 1.0). The area per municipality is computed by WorldFires by crossing the perimeter with those boundaries, so it may differ slightly from each country’s official figure.